Question
Grading Test and Plasticity Test (LL, PL, PI) for every:
Question
Laboratory Compaction Test and Quality Test (Grading, Plasticity, and Abrasion) for every
Question
California Bearing Ratio (CBR) Test for every:
Question
For every ____ of compacted depth at least ____ in situ density tests for every ____ or fraction thereof.
Question
In some areas where conventional base course materials are scarce or non-available, the use of ___ weathered limestone blended with ___ crushed stones or gravel shall be allowed, provided that the blended materials meet the requirements of this Item.
Question
The fraction passing the No. 200 sieve (0.075mm) shall not be greater than ___ of the fraction passing the No. 40 sieve (0.425mm).
Question
According to AASHTO T89 and T90, the fraction passing the No. 40 sieve (0.425mm) shall have a LL of not greater than ___ and PI of not greater than ___.
Question
According to AASHTO T96, the course portion retained on a No. 10 sieve (2mm) shall have a mass percent of wear of ___ max by the Los Angeles Abrasion Test.
Question
According to AASHTO T193, the material passing 19mm sieve shall have a soaked CBR value of not less than ___.
Question
Filler shall be taken from sources approved by the engineer, free from hard slumps, and shall not contain more than ___ of material retained on the No.4 sieve (4.75mm).
Item 202 Crushed Aggregate Base Course
Score
0 / 10
Correct rate
0%
Correct: 0
Incorrect: 0
Unanswered: 10
Question list
1
Grading Test and Plasticity Test (LL, PL, PI) for every:300cu.m
2
Laboratory Compaction Test and Quality Test (Grading, Plasticity, and Abrasion) for every1500cu.m
3
California Bearing Ratio (CBR) Test for every:2500cu.m
4
For every ____ of compacted depth at least ____ in situ density tests for every ____ or fraction thereof.150mm, three, 500sq.m
5
In some areas where conventional base course materials are scarce or non-available, the use of ___ weathered limestone blended with ___ crushed stones or gravel shall be allowed, provided that the blended materials meet the requirements of this Item.40%, 60%
6
The fraction passing the No. 200 sieve (0.075mm) shall not be greater than ___ of the fraction passing the No. 40 sieve (0.425mm).2/3
7
According to AASHTO T89 and T90, the fraction passing the No. 40 sieve (0.425mm) shall have a LL of not greater than ___ and PI of not greater than ___.25, 6
8
According to AASHTO T96, the course portion retained on a No. 10 sieve (2mm) shall have a mass percent of wear of ___ max by the Los Angeles Abrasion Test.45%
9
According to AASHTO T193, the material passing 19mm sieve shall have a soaked CBR value of not less than ___.80%
10
Filler shall be taken from sources approved by the engineer, free from hard slumps, and shall not contain more than ___ of material retained on the No.4 sieve (4.75mm).15%
11
Aggregate base course will be measured by _________cubic meter
12
Permitted variation from design thickness of layer+/- 10mm
13
Permitted variation from design level of surface+5mm/-10mm
14
Permitted surface irregularity measured by 3m straight edge5mm
15
Permitted variation from design crossfall or camber+/- 0.2%
16
Permitted variation from design longitudinal grade over 25m in length+/- 0.1%
17
Fractured Face Test for every:1500cu.m
18
According to AASHTO T96, the course portion retained on a No. 10 sieve (2mm) shall have not less than ___ of at least 1 fractured face.50%