Plumbing Code 1.1

22問 • 13日前

ユーザ名非公開

通報

問題一覧

It is permitted to drill and tap a vent pipe to connect an indirect waste pipe.

false

A connection to the public sewer, or private sewage disposal system, is required for

buildings with plumbing fixtures

Surfaces to be joined by soldering or brazed shall be cleaned bright by

mechanical or manual means

Water that is safe for people to drink is referred to by this code as __\.

potable water

Threaded pipe (IP.S.) 3/4 inch, except for gas piping, installed horizontally shall be supported at approximately ___.

10-foot intervals

A standard that is an extensive compilation of provision covering broad subject matter is the definition for ___.

code

The restroom facilities in a private day care center are classified as public use.

true

In seismic zone 1 and 2, hubless cast iron piping 5 inches or larger suspended in exposed locations over high traffic areas, and over four feet in length, shall be provided with support on both sides of the coupling

false

All design, construction, and workmanship shall be in conformity with ___.

accepted engineering practices

The minimum distance from a side wall or partition to the center of a urinal shall be ___ inches.

Galvanized sheet steel of not less than 16 U.S. gauge may be used to make dishwashing sinks for ___.

restaurants

Tub waste openings in framed construction shall be protected by ___.

metal collars or screens

A pressure surge-absorbing device operating through the compressibility of air is called a(an)___.

air chamber

Test gauges shall not have a pressure range more than __ the test pressure.

twice

The overflow pipe from a fixture shall be connected on the ___.

house or inlet side of the fixture trap

Fixture connections between drainage pipes and water closets shall be made with ___.

flanges

PEX piping may be coupled together with shielded couplings.

false

PEX is the definition for

cross-linked polyethylene

Disposal of sewage, or other liquid waste, shall be by means of ___.

the drainage system of the building or premises

The distance between the center of urinal shall not be less than ___.

24”

A document, the main text of which contains only mandatory provisions using the word "shall" to indicate requirements, is best described as a ___.

standard

All trenches deeper than the footing of any building or structure and paralleling the same shall be at least ___.

each floor not to exceed 15ft

消防救助

消防救助

ドローン

ドローン

車両救助

車両救助

酸欠

酸欠

都市型ロープレスキュー

都市型ロープレスキュー

車両救助

車両救助

スイフトウォーターレスキュー

スイフトウォーターレスキュー

資機材

資機材

土砂と防災

土砂と防災

酸欠

酸欠

都市型ロープレスキュー

都市型ロープレスキュー

消防救助

消防救助

スイフトウォーターレスキュー

スイフトウォーターレスキュー

資機材

資機材

土砂と防災

土砂と防災

第1章②　消防関係法令（全類共通）

第1章②　消防関係法令（全類共通）

学科問題(重要数字)

学科問題(重要数字)

半導体製造/集積回路組立2級筆記(A郡真偽法)

ユーザ名非公開 · 37問 · 5日前

半導体製造/集積回路組立2級筆記(A郡真偽法)

半導体

半導体

半導体

半導体

問題一覧

It is permitted to drill and tap a vent pipe to connect an indirect waste pipe.

false

A connection to the public sewer, or private sewage disposal system, is required for

buildings with plumbing fixtures

Surfaces to be joined by soldering or brazed shall be cleaned bright by

mechanical or manual means

Water that is safe for people to drink is referred to by this code as __\.

potable water

Threaded pipe (IP.S.) 3/4 inch, except for gas piping, installed horizontally shall be supported at approximately ___.

10-foot intervals

A standard that is an extensive compilation of provision covering broad subject matter is the definition for ___.

code

The restroom facilities in a private day care center are classified as public use.

true

false

All design, construction, and workmanship shall be in conformity with ___.

accepted engineering practices

The minimum distance from a side wall or partition to the center of a urinal shall be ___ inches.

Galvanized sheet steel of not less than 16 U.S. gauge may be used to make dishwashing sinks for ___.

restaurants

Tub waste openings in framed construction shall be protected by ___.

metal collars or screens

A pressure surge-absorbing device operating through the compressibility of air is called a(an)___.

air chamber

Test gauges shall not have a pressure range more than __ the test pressure.

twice

The overflow pipe from a fixture shall be connected on the ___.

house or inlet side of the fixture trap

Fixture connections between drainage pipes and water closets shall be made with ___.

flanges

PEX piping may be coupled together with shielded couplings.

false

PEX is the definition for

cross-linked polyethylene

Disposal of sewage, or other liquid waste, shall be by means of ___.

the drainage system of the building or premises

The distance between the center of urinal shall not be less than ___.

24”

A document, the main text of which contains only mandatory provisions using the word "shall" to indicate requirements, is best described as a ___.

standard

All trenches deeper than the footing of any building or structure and paralleling the same shall be at least ___.

each floor not to exceed 15ft