M7c1

18問 • 1年前

問題一覧

Be sure that in workshop all fuels & lubricants that have been contaminated in any way

must collected in containers & returned to the stores for disposal.

It is very important when using pliers for clipping wire to hold them so that the ends of the wire

when snipped off are directed towards the ground . You should never use pliers to tighten or slacken nuts, bolts or screws.

If a circuit breaker is pulled to deactivate a system, a safety tag must be attached to it to indicate this to other maintenance personnel:

On no account should a circuit breaker be reactivated until the person who isolated it has been consulted.

During weather radar testing:

should be no fueling operations in progress.

Casualty Breathing check

you must check for 10 second, look to see if the chest is rising, listen near to the face for breathing sound, and feel for a breath on the cheek.

Class A Solid materials, usually of an organic nature

include wood, paper, cloth, rubber and some plastic.

Class C Fires

involving gases or liquefied gases such as acetylene, methane and propane, etc.

Chemical Foam fire extinguisher can use on

Class A& B fires only.

In burning metals, the proper type of fire extinguisher is

special dry powder.

Wear cap or helmet if:

your hair is long.

Protect your eyes when using

drill, grinding and milling machines.

When grinding a chisel edge on a grinding wheel

the guard must never be removedor disabled. The slight inconvenience they cause is more than compensated for by the added safety, they provide.

It is always good practice:

to notify anyone in the immediate area prior to your work commencing.

The guards and safety covers found on many tools have been put there:

to protect the operator.

Dull cutting tools:

present a greater threat of injury than sharp tools since a dull or improperly sharpened tool requires excessive forces to do its job.

Data regarding the fire and explosion hazard of any material or substance used in the hangar, as well as data about storage and handling precautions, can be found

in the associated material safety data sheet (MSDS)

When turbine engines are being ground run, there is a personal danger from

the intake and the exhaust.

The maximum value of current at which a person holding live electrodes canlet go of them

is from 0.5mA – 10mA.

mod5 training

mod5 training

M6c1

M6c1

M6c2

M6c2

M6c3

M6c3

M6c4

M6c4

M6c5

M6c5

M6c6

M6c6

M6c7

M6c7

M6c8

M6c8

M6c9

M6c9

M6c10

M6c10

M6c11

M6c11

M7c2

M7c2

M7c3

M7c3

M7c4

M7c4

M10c1

M10c1

M7c5

M7c5

問題一覧

Be sure that in workshop all fuels & lubricants that have been contaminated in any way

must collected in containers & returned to the stores for disposal.

It is very important when using pliers for clipping wire to hold them so that the ends of the wire

when snipped off are directed towards the ground . You should never use pliers to tighten or slacken nuts, bolts or screws.

If a circuit breaker is pulled to deactivate a system, a safety tag must be attached to it to indicate this to other maintenance personnel:

On no account should a circuit breaker be reactivated until the person who isolated it has been consulted.

During weather radar testing:

should be no fueling operations in progress.

Casualty Breathing check

you must check for 10 second, look to see if the chest is rising, listen near to the face for breathing sound, and feel for a breath on the cheek.

Class A Solid materials, usually of an organic nature

include wood, paper, cloth, rubber and some plastic.

Class C Fires

involving gases or liquefied gases such as acetylene, methane and propane, etc.

Chemical Foam fire extinguisher can use on

Class A& B fires only.

In burning metals, the proper type of fire extinguisher is

special dry powder.

Wear cap or helmet if:

your hair is long.

Protect your eyes when using

drill, grinding and milling machines.

When grinding a chisel edge on a grinding wheel

the guard must never be removedor disabled. The slight inconvenience they cause is more than compensated for by the added safety, they provide.

It is always good practice:

to notify anyone in the immediate area prior to your work commencing.

The guards and safety covers found on many tools have been put there:

to protect the operator.

Dull cutting tools:

present a greater threat of injury than sharp tools since a dull or improperly sharpened tool requires excessive forces to do its job.

Data regarding the fire and explosion hazard of any material or substance used in the hangar, as well as data about storage and handling precautions, can be found

in the associated material safety data sheet (MSDS)

When turbine engines are being ground run, there is a personal danger from

the intake and the exhaust.

The maximum value of current at which a person holding live electrodes canlet go of them

is from 0.5mA – 10mA.