暗記メーカー

暗記メーカー

​
ログイン
M7c13
10問 • 1年前
  • ユーザ名非公開
    • 通報

    問題一覧

  • 1

    Check for broken wires …………………… as serious laceration can occur. Broken wires are indicated where the cloth gets caught on the cable. Broken wires which lay flat can be difficult to detect.

    Rub a cloth (rag) along the length of the cable in both directions, do not use bare hands

  • 2

    HTS aircraft control cable are protected from corrosion

    be Galvanizing

  • 3

    After swaging an end fitting onto a control cable, a visual inspection for cracks and distortion is performed and then the cable is proof loaded to

    50% of the minimum breaking loud for British specification cables and 60% for American specification cables.

  • 4

    A control cable is proof loaded to ensure

    the end fitting on the cable are secure

  • 5

    A typical modern tensiometer is the Pacific T5 tensiometer It has a set of risers. The tensiometer chart identifies which riser is to be used with each cable size

    Fit the correct riser and correct chart to the tensiometer.

  • 6

    Checking for cable tension for

    looking for full and free movement

  • 7

    Swaging of cable end fitting is checked by

    using a go no go gauge on the barrel.

  • 8

    wet arc tracking is a fault caused

    by insulation damage

  • 9

    A cable should be replaced when individual wires

    are worn greater than 40%

  • 10

    The check for a cable pulling out of a swaged fitting is by looking for

    a shiny surface on the cable near the fitting

    • mod5 training

    mod5 training

    ユーザ名非公開 · 14問 · 1年前

    mod5 training

    mod5 training

    14問 • 1年前
    ユーザ名非公開

    M6c1

    M6c1

    ユーザ名非公開 · 22問 · 1年前

    M6c1

    M6c1

    22問 • 1年前
    ユーザ名非公開

    M6c2

    M6c2

    ユーザ名非公開 · 20問 · 1年前

    M6c2

    M6c2

    20問 • 1年前
    ユーザ名非公開

    M6c3

    M6c3

    ユーザ名非公開 · 52問 · 1年前

    M6c3

    M6c3

    52問 • 1年前
    ユーザ名非公開

    M6c4

    M6c4

    ユーザ名非公開 · 26問 · 1年前

    M6c4

    M6c4

    26問 • 1年前
    ユーザ名非公開

    M6c5

    M6c5

    ユーザ名非公開 · 48問 · 1年前

    M6c5

    M6c5

    48問 • 1年前
    ユーザ名非公開

    M6c6

    M6c6

    ユーザ名非公開 · 27問 · 1年前

    M6c6

    M6c6

    27問 • 1年前
    ユーザ名非公開

    M6c7

    M6c7

    ユーザ名非公開 · 15問 · 1年前

    M6c7

    M6c7

    15問 • 1年前
    ユーザ名非公開

    M6c8

    M6c8

    ユーザ名非公開 · 15問 · 1年前

    M6c8

    M6c8

    15問 • 1年前
    ユーザ名非公開

    M6c9

    M6c9

    ユーザ名非公開 · 17問 · 1年前

    M6c9

    M6c9

    17問 • 1年前
    ユーザ名非公開

    M6c10

    M6c10

    ユーザ名非公開 · 18問 · 1年前

    M6c10

    M6c10

    18問 • 1年前
    ユーザ名非公開

    M6c11

    M6c11

    ユーザ名非公開 · 44問 · 1年前

    M6c11

    M6c11

    44問 • 1年前
    ユーザ名非公開

    M7c1

    M7c1

    ユーザ名非公開 · 18問 · 1年前

    M7c1

    M7c1

    18問 • 1年前
    ユーザ名非公開

    M7c2

    M7c2

    ユーザ名非公開 · 11問 · 1年前

    M7c2

    M7c2

    11問 • 1年前
    ユーザ名非公開

    M7c3

    M7c3

    ユーザ名非公開 · 39問 · 1年前

    M7c3

    M7c3

    39問 • 1年前
    ユーザ名非公開

    M7c4

    M7c4

    ユーザ名非公開 · 21問 · 1年前

    M7c4

    M7c4

    21問 • 1年前
    ユーザ名非公開

    M10c1

    M10c1

    ユーザ名非公開 · 15問 · 1年前

    M10c1

    M10c1

    15問 • 1年前
    ユーザ名非公開

    M7c5

    M7c5

    ユーザ名非公開 · 11問 · 1年前

    M7c5

    M7c5

    11問 • 1年前
    ユーザ名非公開

    問題一覧

  • 1

    Check for broken wires …………………… as serious laceration can occur. Broken wires are indicated where the cloth gets caught on the cable. Broken wires which lay flat can be difficult to detect.

    Rub a cloth (rag) along the length of the cable in both directions, do not use bare hands

  • 2

    HTS aircraft control cable are protected from corrosion

    be Galvanizing

  • 3

    After swaging an end fitting onto a control cable, a visual inspection for cracks and distortion is performed and then the cable is proof loaded to

    50% of the minimum breaking loud for British specification cables and 60% for American specification cables.

  • 4

    A control cable is proof loaded to ensure

    the end fitting on the cable are secure

  • 5

    A typical modern tensiometer is the Pacific T5 tensiometer It has a set of risers. The tensiometer chart identifies which riser is to be used with each cable size

    Fit the correct riser and correct chart to the tensiometer.

  • 6

    Checking for cable tension for

    looking for full and free movement

  • 7

    Swaging of cable end fitting is checked by

    using a go no go gauge on the barrel.

  • 8

    wet arc tracking is a fault caused

    by insulation damage

  • 9

    A cable should be replaced when individual wires

    are worn greater than 40%

  • 10

    The check for a cable pulling out of a swaged fitting is by looking for

    a shiny surface on the cable near the fitting