Weekly Test 1

通報

問題一覧

A water heater is classified as?

Plumbing Appliance

Elastomeric gasketed and rubber-ring joints shall comply with ___________ installation standard

IAPMO

Depth of the molten pig lead in a caulked joint

25.4 mm

Copper tubing shall be fully externally protected with a/an _______________ and fiberglass wrapping installed inside a split rigid casing whenever installed underground.

bitumastic coating

Wiped lead joints shall have an exposed surface on each side of a joint not less than _________.

19 mm

Copper tube for water supply piping shall have a weight of not less than ________.

Type L

Who is the current chairman of the Board of Examiners for Master Plumber?

Reynald B. Ilagan

A plumbing permit shall become null and void if the plumbing work has been suspended or abandoned for a period of ___________.

120 days

Code on Sanitation of the Philippines

PD 856

Common maximum service temperature rating of PVC

140 deg. F

Every building where ______________ shall have a sewer service connection to a public or private sewer systems.

plumbing fixtures are installed

A hose connection with two-gated outlets permitting two connections of the same or smaller coupling diameter to be taken from a single supply line.

Wye

Each fixture directly connected to the drainage system shall be equipped with a ___________.

water-sealed trap

For caulked-on closet ring, the minimum overall depth shall be:

2”

IPS shall be supported at _______ intervals for piping 19 mm diameter and smaller.

3 m

Preferred when a piece of pipe needed is shorter than 150 cm long

Double Hub

(ANSI) Pipe Color code for Fire Quenching

Red with White Lettering

The Plumbing Code has been in existence for almost __________ since its promulgation before it has been amended

40 years

The year when NAMPAP was organized and registered with the Securities and Exchange Commission

1935

When was the National Plumbing Code promulgated and approved by the Malacañang?

January 28, 1959

Tube made of plastic material and colored black. The cross-sectional shape is normally oval and is denoted by its outside diameter or O.D.

Polybutylene

Integrated within an air accumulator vessel which is designed to discharge a predetermined quantity of water into fixtures for flushing purposes

Flushometer Tank

Distance of bottom of all pipe tranches to the footing of any adjacent building or structure parallel to it

45 degrees

The birth of the plumbing profession in the Philippines is traced back to the _______ century.

17th

Trap arm size of Laundry Tub

38 mm

Date of the Accreditation of NAMPAP

October 2, 1975

In a plumbing unit, how many floor drains are included?

Vertical support of _________ is placed not less than every other storey height.

Screwed Pipe

The Administrative Authority must be notified at least ___ working days before such inspection is intended.

ASTM means?

American Society for Testing and Materials

What principle number: No water closet shall be located in a room or compartment which is not properly lighted and ventilated.

Principle No. 16

1 fixture unit is equal to?

1 cu. ft. per minute

The distance of water closet or bidet center to center

0.75 m

Each member of the board, shall at the time of his appointment be at least _____ of age.

30 years

An open return bend usually made up of two 90° bends

Return Bend

Any change, addition or modification in construction or occupancy

Alteration

Minimum weight of a lead for flashing or vent terminals

14.63 kg per sq.m.

A registered master plumber must not supplant another Registered Master Plumber after definite steps have already been taken toward his/her being commissioned to perform the contract

Code of Ethics No. 2

Color for Type M copper pipe

Red

What is not included in a plumbing unit?

Urinal

Voids between pipes and sleeves through concrete floors in the ground shall be appropriately sealed with ________.

Bitumen

A pipe flange that is not drilled for bolt holes.

Blank Flange

What will happen if a drainage piping is placed at slope of 10mm/m due to structural conditions?

Decrease in DFU loading

What section of RA 1378 enumerates the qualification for persons applying for examination?

Section 12

What is the accreditation number of NAMPAP?

All plumbing plans, drawings, diagrams, etc. shall be submitted in ___ sets for permit application.

The top edge of a receptacle from where water overflows.

Flood Level Rim

A pipe or conduit for carrying sewage and wastewater.

Sewer

This examination subject in Master Plumbing was originally split into two.

Practical Problems

An adjustable tubing connection, consisting of a compression nut, a friction ring, and a compression washer, designed to fit a threaded adapter fitting or a standard taper pipe thread.

Slip Joint

YT1 Materials Engineer EXAM

YT1 Materials Engineer EXAM

YT2 Materials Engineer EXAM

YT2 Materials Engineer EXAM

Project Engineer YT 1

Project Engineer YT 1

Project Engineer EXAM

ユーザ名非公開 · 62問 · 13日前

Project Engineer EXAM

62問 • 13日前

Project Engineer EXAM 68

Project Engineer EXAM 68

Project Engineer EXAM 82

Project Engineer EXAM 82

July 2023 PE Refresher

ユーザ名非公開 · 70問 · 13日前

July 2023 PE Refresher

70問 • 13日前

August 2019 Special PE Exam

ユーザ名非公開 · 93問 · 13日前

August 2019 Special PE Exam

RNPCP Chapter 1 to 5

RNPCP Chapter 1 to 5

Plumbing Code 4

Plumbing Code 4

Plumbing Code 5

Plumbing Code 5

Plumbing Code 6

Plumbing Code 6

Plumbing Code 7

Plumbing Code 7

Plumbing Code 8

Plumbing Code 8

Plumbing Code 3

Plumbing Code 3

Sanitation, Plumbing Design, and Installation 2

ユーザ名非公開 · 97問 · 13日前

Sanitation, Plumbing Design, and Installation 2

97問 • 13日前

Sanitation, Plumbing Design, and Installation 1

ユーザ名非公開 · 99問 · 13日前

Sanitation, Plumbing Design, and Installation 1

99問 • 13日前

Sanitation, Plumbing Design, and Installation 3

ユーザ名非公開 · 96問 · 13日前

Sanitation, Plumbing Design, and Installation 3

96問 • 13日前

Sanitation, Plumbing Design, and Installation 4

ユーザ名非公開 · 95問 · 13日前

Sanitation, Plumbing Design, and Installation 4

95問 • 13日前

Sanitation, Plumbing Design, and Installation 5

ユーザ名非公開 · 97問 · 13日前

Sanitation, Plumbing Design, and Installation 5

97問 • 13日前