ログイン

MPLE
41問 • 13日前
  • ユーザ名非公開
  • 通報

    問題一覧

  • 1

    What is the DFU of a private water closet?

    4

  • 2

    The water pressure to be used for water piping tests

    150% working pressure

  • 3

    For flush tank supplies, the available pressure may not be less than ________.

    55.16 kPa

  • 4

    A plumbing permit shall become null and void if the plumbing work is not commenced within _________ from the date of such permit.

    1 year

  • 5

    Sewage or other waste from a plumbing system which may be deleterious to the surface or sub-surface waters shall not be discharged into the ground or into any waterway unless first rendered innocuous through subjection to some acceptable form of treatment.

    Principle #22

  • 6

    The level in a fixture at which water begins to overflow over the top ring of the fixture.

    Flood level

  • 7

    A term applied to those portions of a plumbing system, which have been installed and approved prior to contemplated additions, alterations, or correction, is called

    Existing work

  • 8

    This consists of a pliable rubber cup and handle, and is capable of creating both a positive pressure (by forcing the cup down), and a negative pressure (vacuum) when pulled away from the fixture. Variations on the design are typically limited to the size of the cup and length of the handle.

    Plunger

  • 9

    A beginner at the trade who usually serves for 3 to 5 years as a helper to a journeyman.A beginner at the trade who usually serves for 3 to 5 years as a helper to a journeyman.

    Apprentice Plumber

  • 10

    Who is the overall chairman in-charge on the Revision & Upgrading of the National Plumbing Code of the Philippines?

    Engr. Camilet

  • 11

    What Section of the RA 1378 refers to the qualifications of the applicants for registration and examination for Master Plumber?

    Section 12

  • 12

    In _______, the Board of Examiners for Master Plumbers and the NAMPAP prepared a curriculum for plumbing engineering.

    1966-1969

  • 13

    How many years has the plumbing code been in existence since its promulgation before it has been amended?

    40 years

  • 14

    A permit is not required for repair that involve only ________.

    the working parts of faucet and valves

  • 15

    How many sets of approved plans, specifications, computations, and related data shall be retained by the Administrative Authority?

    1

  • 16

    This pipe is also known as Terracotta Pipe.

    Vitrified Clay Pipe

  • 17

    This type of Cast Iron is recommended when the length of a pipe needed is more than 150 cm long.

    Single Hub

  • 18

    This pipe shall be supported at intervals not exceeding 1.20 m at centers with a rigid vertical back-up.

    Lead Pipe

  • 19

    A fitting with adjacent reverse bends and shaped like the letter "S"

    Double-Bend Fitting

  • 20

    The distance of water closet or bidet from center to side

    0.375 m

  • 21

    How many faucets are there in the Plumbing Unit according to the Revised National Plumbing Code?

    4

  • 22

    Which material ultimately seals a caulked or bell and spigot joint?

    Pig Lead

  • 23

    Shall be responsible for the maintenance of the plumbing systems.

    Owner or owner’s agent

  • 24

    A system of collection, transportation, treatment, and disposal of sewage is called __________.

    Sewage disposal system

  • 25

    Any branch in a building drain other than the primary branch.

    Secondary Branch

  • 26

    Minimum air pressure of air test ______ kPa

    34.5

  • 27

    The NAMPAP president who spearheaded the update of the Revised National Plumbing Code.

    Jaime M. Cabase

  • 28

    A Backflow Prevention device that consists of a body, a checking member and an atmospheric opening.

    AVB

  • 29

    Plumbing Law of the Philippines was signed by Pres. Ramon Magsaysay on _________.

    June 18, 1955

  • 30

    Type of pump used to distribute water within a building or residence, when an upfeed system cannot provide adequate pressure to supply fixtures with potable water. Pump that increases low water pressure and flow. ___________.

    Booster Pump

  • 31

    What is the vent pipe system in Plumbing which liquid waste can flow through?

    Wet Vent

  • 32

    It is the discharge from any fixture, appliance or appurtenance in connection with a plumbing system which does not receive fecal matter.

    Liquid Waste

  • 33

    A pipe which makes an angle of more than 45 degrees from the horizontal is considered ________.

    vertical

  • 34

    1 gpm = ________ L/s

    0.0631

  • 35

    Maximum height of water closet for the handicapped and disabled (BP344)

    0.45 m

  • 36

    How many female office employees are suited for 5 lavatories?

    200

  • 37

    Building sewers shall be tested by completely filling the sewer line with water from the lowest to

    the highest point

  • 38

    Maximum number of fixtures to be served by a grease trap

    4

  • 39

    What is a vent connecting one or more individual vents with a stack vent or vent stack.

    branch

  • 40

    Horizontal distance of vertical vent pipes for outdoor installations to any part of the roof that is used for other purposes.

    3.00 m

  • 41

    Where can a cleanout be located?

    all of these

  • YT1 Materials Engineer EXAM

    YT1 Materials Engineer EXAM

    ユーザ名非公開 · 100問 · 13日前

    YT1 Materials Engineer EXAM

    YT1 Materials Engineer EXAM

    100問 • 13日前
    ユーザ名非公開

    YT2 Materials Engineer EXAM

    YT2 Materials Engineer EXAM

    ユーザ名非公開 · 100問 · 13日前

    YT2 Materials Engineer EXAM

    YT2 Materials Engineer EXAM

    100問 • 13日前
    ユーザ名非公開

    Project Engineer YT 1

    Project Engineer YT 1

    ユーザ名非公開 · 100問 · 13日前

    Project Engineer YT 1

    Project Engineer YT 1

    100問 • 13日前
    ユーザ名非公開

    Project Engineer EXAM

    Project Engineer EXAM

    ユーザ名非公開 · 62問 · 13日前

    Project Engineer EXAM

    Project Engineer EXAM

    62問 • 13日前
    ユーザ名非公開

    Project Engineer EXAM 68

    Project Engineer EXAM 68

    ユーザ名非公開 · 100問 · 13日前

    Project Engineer EXAM 68

    Project Engineer EXAM 68

    100問 • 13日前
    ユーザ名非公開

    Project Engineer EXAM 82

    Project Engineer EXAM 82

    ユーザ名非公開 · 100問 · 13日前

    Project Engineer EXAM 82

    Project Engineer EXAM 82

    100問 • 13日前
    ユーザ名非公開

    July 2023 PE Refresher

    July 2023 PE Refresher

    ユーザ名非公開 · 70問 · 13日前

    July 2023 PE Refresher

    July 2023 PE Refresher

    70問 • 13日前
    ユーザ名非公開

    August 2019 Special PE Exam

    August 2019 Special PE Exam

    ユーザ名非公開 · 93問 · 13日前

    August 2019 Special PE Exam

    August 2019 Special PE Exam

    93問 • 13日前
    ユーザ名非公開

    RNPCP Chapter 1 to 5

    RNPCP Chapter 1 to 5

    ユーザ名非公開 · 86問 · 13日前

    RNPCP Chapter 1 to 5

    RNPCP Chapter 1 to 5

    86問 • 13日前
    ユーザ名非公開

    Plumbing Code 4

    Plumbing Code 4

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 4

    Plumbing Code 4

    100問 • 13日前
    ユーザ名非公開

    Plumbing Code 5

    Plumbing Code 5

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 5

    Plumbing Code 5

    100問 • 13日前
    ユーザ名非公開

    Plumbing Code 6

    Plumbing Code 6

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 6

    Plumbing Code 6

    100問 • 13日前
    ユーザ名非公開

    Plumbing Code 7

    Plumbing Code 7

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 7

    Plumbing Code 7

    100問 • 13日前
    ユーザ名非公開

    Plumbing Code 8

    Plumbing Code 8

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 8

    Plumbing Code 8

    100問 • 13日前
    ユーザ名非公開

    Plumbing Code 3

    Plumbing Code 3

    ユーザ名非公開 · 100問 · 13日前

    Plumbing Code 3

    Plumbing Code 3

    100問 • 13日前
    ユーザ名非公開

    Sanitation, Plumbing Design, and Installation 2

    Sanitation, Plumbing Design, and Installation 2

    ユーザ名非公開 · 97問 · 13日前

    Sanitation, Plumbing Design, and Installation 2

    Sanitation, Plumbing Design, and Installation 2

    97問 • 13日前
    ユーザ名非公開

    Sanitation, Plumbing Design, and Installation 1

    Sanitation, Plumbing Design, and Installation 1

    ユーザ名非公開 · 99問 · 13日前

    Sanitation, Plumbing Design, and Installation 1

    Sanitation, Plumbing Design, and Installation 1

    99問 • 13日前
    ユーザ名非公開

    Sanitation, Plumbing Design, and Installation 3

    Sanitation, Plumbing Design, and Installation 3

    ユーザ名非公開 · 96問 · 13日前

    Sanitation, Plumbing Design, and Installation 3

    Sanitation, Plumbing Design, and Installation 3

    96問 • 13日前
    ユーザ名非公開

    Sanitation, Plumbing Design, and Installation 4

    Sanitation, Plumbing Design, and Installation 4

    ユーザ名非公開 · 95問 · 13日前

    Sanitation, Plumbing Design, and Installation 4

    Sanitation, Plumbing Design, and Installation 4

    95問 • 13日前
    ユーザ名非公開

    Sanitation, Plumbing Design, and Installation 5

    Sanitation, Plumbing Design, and Installation 5

    ユーザ名非公開 · 97問 · 13日前

    Sanitation, Plumbing Design, and Installation 5

    Sanitation, Plumbing Design, and Installation 5

    97問 • 13日前
    ユーザ名非公開

    問題一覧

  • 1

    What is the DFU of a private water closet?

    4

  • 2

    The water pressure to be used for water piping tests

    150% working pressure

  • 3

    For flush tank supplies, the available pressure may not be less than ________.

    55.16 kPa

  • 4

    A plumbing permit shall become null and void if the plumbing work is not commenced within _________ from the date of such permit.

    1 year

  • 5

    Sewage or other waste from a plumbing system which may be deleterious to the surface or sub-surface waters shall not be discharged into the ground or into any waterway unless first rendered innocuous through subjection to some acceptable form of treatment.

    Principle #22

  • 6

    The level in a fixture at which water begins to overflow over the top ring of the fixture.

    Flood level

  • 7

    A term applied to those portions of a plumbing system, which have been installed and approved prior to contemplated additions, alterations, or correction, is called

    Existing work

  • 8

    This consists of a pliable rubber cup and handle, and is capable of creating both a positive pressure (by forcing the cup down), and a negative pressure (vacuum) when pulled away from the fixture. Variations on the design are typically limited to the size of the cup and length of the handle.

    Plunger

  • 9

    A beginner at the trade who usually serves for 3 to 5 years as a helper to a journeyman.A beginner at the trade who usually serves for 3 to 5 years as a helper to a journeyman.

    Apprentice Plumber

  • 10

    Who is the overall chairman in-charge on the Revision & Upgrading of the National Plumbing Code of the Philippines?

    Engr. Camilet

  • 11

    What Section of the RA 1378 refers to the qualifications of the applicants for registration and examination for Master Plumber?

    Section 12

  • 12

    In _______, the Board of Examiners for Master Plumbers and the NAMPAP prepared a curriculum for plumbing engineering.

    1966-1969

  • 13

    How many years has the plumbing code been in existence since its promulgation before it has been amended?

    40 years

  • 14

    A permit is not required for repair that involve only ________.

    the working parts of faucet and valves

  • 15

    How many sets of approved plans, specifications, computations, and related data shall be retained by the Administrative Authority?

    1

  • 16

    This pipe is also known as Terracotta Pipe.

    Vitrified Clay Pipe

  • 17

    This type of Cast Iron is recommended when the length of a pipe needed is more than 150 cm long.

    Single Hub

  • 18

    This pipe shall be supported at intervals not exceeding 1.20 m at centers with a rigid vertical back-up.

    Lead Pipe

  • 19

    A fitting with adjacent reverse bends and shaped like the letter "S"

    Double-Bend Fitting

  • 20

    The distance of water closet or bidet from center to side

    0.375 m

  • 21

    How many faucets are there in the Plumbing Unit according to the Revised National Plumbing Code?

    4

  • 22

    Which material ultimately seals a caulked or bell and spigot joint?

    Pig Lead

  • 23

    Shall be responsible for the maintenance of the plumbing systems.

    Owner or owner’s agent

  • 24

    A system of collection, transportation, treatment, and disposal of sewage is called __________.

    Sewage disposal system

  • 25

    Any branch in a building drain other than the primary branch.

    Secondary Branch

  • 26

    Minimum air pressure of air test ______ kPa

    34.5

  • 27

    The NAMPAP president who spearheaded the update of the Revised National Plumbing Code.

    Jaime M. Cabase

  • 28

    A Backflow Prevention device that consists of a body, a checking member and an atmospheric opening.

    AVB

  • 29

    Plumbing Law of the Philippines was signed by Pres. Ramon Magsaysay on _________.

    June 18, 1955

  • 30

    Type of pump used to distribute water within a building or residence, when an upfeed system cannot provide adequate pressure to supply fixtures with potable water. Pump that increases low water pressure and flow. ___________.

    Booster Pump

  • 31

    What is the vent pipe system in Plumbing which liquid waste can flow through?

    Wet Vent

  • 32

    It is the discharge from any fixture, appliance or appurtenance in connection with a plumbing system which does not receive fecal matter.

    Liquid Waste

  • 33

    A pipe which makes an angle of more than 45 degrees from the horizontal is considered ________.

    vertical

  • 34

    1 gpm = ________ L/s

    0.0631

  • 35

    Maximum height of water closet for the handicapped and disabled (BP344)

    0.45 m

  • 36

    How many female office employees are suited for 5 lavatories?

    200

  • 37

    Building sewers shall be tested by completely filling the sewer line with water from the lowest to

    the highest point

  • 38

    Maximum number of fixtures to be served by a grease trap

    4

  • 39

    What is a vent connecting one or more individual vents with a stack vent or vent stack.

    branch

  • 40

    Horizontal distance of vertical vent pipes for outdoor installations to any part of the roof that is used for other purposes.

    3.00 m

  • 41

    Where can a cleanout be located?

    all of these