RNPCP Chapter 1 to 5

通報

問題一覧

RA 1378

Plumbing Law

Set/s of plumbing plans, drawings, diagrams, and other documents to be submitted for the application of permit.

6 sets

Set/s of approved plans, specifications, and data to be retained by the Administrative Authority.

1 set

Set/s of entire plans and specifications to be returned to the applicant.

2 sets

Set/s of entire plans and specifications to be returned to the Owner.

2 sets

Set/s of entire plans and specifications to be kept at job site

1 set

Expiration of plumbing permit if work is not commenced from the date of issuance

1 year

Expiration of plumbing permit if the work has been suspended or abandoned.

120 days

Percentage of original fee to be paid for the renewal of permit.

50%

Request for inspection for the replacement of an existing equipment shall be filed not more than ______ after such replacement work is completed.

72 hrs

Request for inspection shall be filed with the Administrative Authority at least _____ before such inspection is intended.

3 working days

Alley means any public space, public or park ______ on width.

2m to 3m

Court is bounded by ______ by the walls of building

2 or more sides

Yards are open, unoccupied, _____ from ground to sky.

unobstructed

Group vent is a branch vent that performs its functions for ___ or more traps

Branch interval which corresponds to a storey height shall be not less than _____.

2.43m

Brazed joints are obtained by joining of metal parts with alloys which melt at temperatures higher than _____, but lower than the melting temperature of the parts to be joined.

449°C

Soldered joints are obtained by joining of metal parts with alloys which melt at temperatures above ___ and below ___.

149°C, 427°C

Distance of the building sewer from the outer face of any building foundation or wall.

0.60m

Mobile Home Park Sewer measures _____ downstream from the last mobile home.

0.60m

Horizontal pipe forms an angle of not more than ___ with the horizontal line.

45°C

Vertical pipe forms an angle of not more than ___ with the vertical line.

45°C

Combustible construction is any structure with structural framework which ignites and burns at temperature of ___ or less.

756°C

Confined space is a room or space having a volume less than _____ with 250kg calorie of the aggregate input rating of all fuel burning applicances installed in that space.

1.4cu.m.

Equivalent of 1 fixture unit to liters per minute

28.3

Equivalent to 1 fixture unit to gallons per minute

7.48

Equivalent of one fixture unit to quartz per minute

Equivalent of one fixture unit to cubic foot per minute

Minimum capacity of a grease interceptor

3 cu.m.

No of traps served by a unit vent

Return bend is usually made of two ___ bends

90°

Recommended slope for horizontal drainage pipes

Recommended slope for 102mm and 152.4mm diameter when impractical; and must be approved by Administrative Authority

Recommended slope for 203mm and larger diameter when impractical; and must be approved by Administrative Authority

0.5%

Vertical installation of double sanitary tees maybe used when the barrel of the fitting is at least ___ pipe size larger than the largest side inlet

The bottom of all pipe trenches deeper than the footing of any adjacent building or structure and parallel to it must be at least ___

45°

Minimum depth of building sewer below the finish ground level

0.30m

Maximum depth of building sewer below the finish ground level

0.60m

Clear height of tunnels above the pipe laid in a trench

0.60m

Maximum length of tunnels is 1/2 the depth of trench or ____.

2.4m

Trenches shall be backfilled in thin layers of ____ above the top of the pipe with clean earth.

0.30m

Minimum thickness of restaurant kitchen and other special use sink, bonderized and galvanized sheet steel.

GA 16 B&S (1.6mm)

Minimum thickness of continuous waste and fixture tailpiece made of seamless drawn brass.

GA 20 B&S (0.8mm)

Least dimension of access panel or utility for fixtures with concealed slip joint connections, provided for inspection and repair.

0.30m

Minimum diameter of tailpiece, continuous waste or waste and overflow for sinks, dishwaters, laundry tubs, bathtubs, urinals and similar fixtures.

1 1/2" or 38mm O.D.

Minimum diameter of tailpiece, continuous waste or waste and overflow for lavatories, drinking fountains, and similar small fixtures.

1 1/4" or 32mm O.D.

Distance of water closet or bidet from its center to any side wall.

0.375m

Distance of water closet or bidet center to center

0.75m

Distance of urinal from its center to any side wall

0.30m

Distance of urinal center to center

0.60m

Minimum depth of finished shower dam, curb or threshold from the outside door.

25.4mm

Min depth of shower dam or threshold measure from the top of the dam or threshold to the top of the drain

51mm to 228mm

Slope of a finished floor of a shower receptor

2% to 4%

Minimum width of a shower door a threshold should accommodate

559mm (22")

Minimum distance between the door or entry to the drain opening

1.2m

Minimum finished interior area of a shower compartment

0.6sqm

Minimum diameter of a circle capable of encompassing a shower compartment

762mm

Minimum area and dimensions of a shower compartment shall be maintained from a point above the shower drain outlet to a height of ________.

1.78m

For shower receptors built above the ground, at least ______ above the top of the finished dam or threshold shall be first lined with sheet lead or copper or with other durable and watertight materials

76mm

Minimum extension of all lining materials upward on the rough jambs of the shower opening above the top of the finished dam or threshold.

76mm

Standard grade of asphalt-impregnated roofing felt for metaling shower sub-pans or linings.

6.8kg

Extension of folds, laps and reinforcing webbing for shower lining or sub-pans in all directions from the corner of the webbing.

101mm

Minimum tensile strength of mesh/webbing for lining or sub-pan

0.9kg/mm

Linings above the finished dam or threshold shall not be nailed or perforated

25.4mm

Minimum weight of lead pans or liners

19.6kg/m2

Minimum thickness of copper pans or liners

GA 24 B&S (0.5mm)

Slope of gutters in public or gang shower rooms

Maximum spacing of gutter drains in public or gang shower rooms

4.9m

Maximum temperature of limit stops for the delivery of hot water (human consumption)

48.88°C

Width of wash sink, when provided with water outlets, shall be considered equivalent to 1 lavatory

608.6mm (24")

Diameter of circular basin, when provided with water outlets, shall be considered equal to 1 lavatory

457.2mm (18")

Ratio of lavatory to number of persons in occupancy where there is exposure to skin contamination with poisonous, infectious, or irritating materials

1:5

Ratio of laundry tray to number of persons

1:50

Ratio of slope sink tray to number of persons

1:100

Ratio of water closet and urinal to number of persons for temporary workingmen

1:30

Distance on each side of the urinal to be lined with non-absorbent materials

0.6m

Height above the floor of the urinal to be lined with non-absorbent materials

1.2m

Ratio of drinking fountain to number of persons in public buildings

1:75

On top of first 75 persons, provide 1 additional drinking fountain for each _____ persons thereafter

150

Notice to Administrative Authority that the work is ready for inspection

3 days

Head of water to be filled on each section of piping under water test

Duration that water shall be kept before start of inspection

15min

Gauge pressure for air test, equivalent to 254mm Mercury in height

34.5kPa

Duration that air pressure shall be held during air test without introduction of additional air

15min

Water piping shall be tested under a water pressure not less than the working pressure under which is to be used plus ____

50%

Air pressure which may be substituted for the water test

344.5kPa

Project Engineer EXAM

Vaantoote · 62問 · 2年前

Project Engineer EXAM

62問 • 2年前

YT1 Materials Engineer EXAM

Vaantoote · 100問 · 2年前

YT1 Materials Engineer EXAM

100問 • 2年前

YT2 Materials Engineer EXAM

Vaantoote · 100問 · 2年前

YT2 Materials Engineer EXAM

100問 • 2年前

Project Engineer YT 1

Project Engineer YT 1

Project Engineer EXAM 68

Project Engineer EXAM 68

Project Engineer EXAM 82

Project Engineer EXAM 82

July 2023 PE Refresher

Vaantoote · 70問 · 1年前

July 2023 PE Refresher

70問 • 1年前

August 2019 Special PE Exam

Vaantoote · 93問 · 1年前

August 2019 Special PE Exam

93問 • 1年前

Plumbing Code 1

Plumbing Code 1

Plumbing Code 2

Plumbing Code 2

Plumbing Code 4

Plumbing Code 4

Plumbing Code 5

Plumbing Code 5

Plumbing Code 6

Plumbing Code 6

Plumbing Code 7

Plumbing Code 7

Plumbing Code 8

Plumbing Code 8

Plumbing Code 3

Plumbing Code 3

Sanitation, Plumbing Design, and Installation 2

Vaantoote · 97問 · 1年前

Sanitation, Plumbing Design, and Installation 2

97問 • 1年前

Sanitation, Plumbing Design, and Installation 1

Vaantoote · 99問 · 1年前

Sanitation, Plumbing Design, and Installation 1

99問 • 1年前

Sanitation, Plumbing Design, and Installation 3

Vaantoote · 96問 · 1年前

Sanitation, Plumbing Design, and Installation 3

96問 • 1年前

Sanitation, Plumbing Design, and Installation 4

Vaantoote · 95問 · 1年前

Sanitation, Plumbing Design, and Installation 4

95問 • 1年前

Sanitation, Plumbing Design, and Installation 5

Vaantoote · 97問 · 1年前

Sanitation, Plumbing Design, and Installation 5

97問 • 1年前

Sanitation, Plumbing Design, and Installation 7

Sanitation, Plumbing Design, and Installation 7

Sanitation, Plumbing Design, and Installation 8

Vaantoote · 98問 · 1年前

Sanitation, Plumbing Design, and Installation 8

98問 • 1年前

Plumbing Tools 1

Vaantoote · 87問 · 1年前

Plumbing Tools 1

87問 • 1年前

Plumbing Tools 2

Vaantoote · 53問 · 1年前

Plumbing Tools 2

53問 • 1年前

Practical Problems and Experiences 1

Practical Problems and Experiences 1

Practical Problems and Experiences 2

Practical Problems and Experiences 2

Practical Problems and Experiences 3

Vaantoote · 99問 · 1年前

Practical Problems and Experiences 3

99問 • 1年前

Practical Problems and Experiences 4

Practical Problems and Experiences 4

PART A - Facilities for the Engineer

Vaantoote · 9問 · 1年前

PART A - Facilities for the Engineer

9問 • 1年前

PART B - Other General Requirements

Vaantoote · 13問 · 1年前

PART B - Other General Requirements

13問 • 1年前

Practical Problems and Experiences 5

Practical Problems and Experiences 5

Practical Problems and Experiences 6

Practical Problems and Experiences 6

Plumbing Arithmetic Terms 1

Vaantoote · 49問 · 1年前

Plumbing Arithmetic Terms 1

49問 • 1年前

Plumbing Arithmetic Terms 2

Vaantoote · 47問 · 1年前

Plumbing Arithmetic Terms 2

47問 • 1年前

Plumbing Arithmetic Terms 3

Vaantoote · 49問 · 1年前

Plumbing Arithmetic Terms 3

49問 • 1年前

Plumbing Arithmetic Terms 4

Vaantoote · 27問 · 1年前

Plumbing Arithmetic Terms 4

27問 • 1年前

Plumbing Code WSFU

Vaantoote · 58問 · 1年前

Plumbing Code WSFU

58問 • 1年前

Practical Problems and Experiences REFRESHER 1

Practical Problems and Experiences REFRESHER 1

Practical Problems and Experiences REFRESHER 2

Vaantoote · 70問 · 1年前

Practical Problems and Experiences REFRESHER 2

70問 • 1年前

Item # and Descriptions

Vaantoote · 24問 · 1年前

Item # and Descriptions

24問 • 1年前

Item 200 Aggregate Subbase Course

Vaantoote · 16問 · 1年前

Item 200 Aggregate Subbase Course

16問 • 1年前

Item 201 Aggregate Base Course

Vaantoote · 16問 · 1年前

Item 201 Aggregate Base Course

16問 • 1年前

Item 202 Crushed Aggregate Base Course

Vaantoote · 18問 · 1年前

Item 202 Crushed Aggregate Base Course

18問 • 1年前

Item 203 Lime Stabilized Road Mix Base Course

Vaantoote · 27問 · 1年前

Item 203 Lime Stabilized Road Mix Base Course

27問 • 1年前

Item 204 Portland Cement Stabilized Road Mix Base Course

Vaantoote · 7問 · 1年前

Item 204 Portland Cement Stabilized Road Mix Base Course

7問 • 1年前

Item 205 Asphalt Stabilized Road Mix Base Course

Vaantoote · 7問 · 1年前

Item 205 Asphalt Stabilized Road Mix Base Course

7問 • 1年前

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

Vaantoote · 13問 · 1年前

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

13問 • 1年前

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

Vaantoote · 11問 · 1年前

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

11問 • 1年前

Item 300 Aggregate Surface Course

Vaantoote · 11問 · 1年前

Item 300 Aggregate Surface Course

11問 • 1年前

Item 301 Bituminous Prime Coat

Vaantoote · 10問 · 1年前

Item 301 Bituminous Prime Coat

10問 • 1年前

Item 303 Bituminous Seal Coat

Vaantoote · 20問 · 1年前

Item 303 Bituminous Seal Coat

20問 • 1年前

RNPCP Chapter 6 to 9

Vaantoote · 94問 · 1年前

RNPCP Chapter 6 to 9

94問 • 1年前

RNPCP Chapter 10 to 13

Vaantoote · 93問 · 1年前

RNPCP Chapter 10 to 13

93問 • 1年前

RNPCP Appendix A and B

Vaantoote · 79問 · 1年前

RNPCP Appendix A and B

79問 • 1年前

Item 311 Portland Cement Concrete Pavement (PART 1)

Vaantoote · 78問 · 1年前

Item 311 Portland Cement Concrete Pavement (PART 1)

78問 • 1年前

Item 311 Portland Cement Concrete Pavement (PART 2)

Vaantoote · 61問 · 1年前

Item 311 Portland Cement Concrete Pavement (PART 2)

Republic Acts

Republic Acts

Plumbing Arithmetic Terms 5

Vaantoote · 68問 · 1年前

Plumbing Arithmetic Terms 5

68問 • 1年前

Item 400 Piling

Vaantoote · 80問 · 1年前

Item 400 Piling

80問 • 1年前

Item 405 Structural Concrete

Vaantoote · 41問 · 1年前

Item 405 Structural Concrete

41問 • 1年前

Item 406 Prestressed Concrete Structures

Vaantoote · 36問 · 1年前

Item 406 Prestressed Concrete Structures

36問 • 1年前

Item 407 Concrete Structures

Vaantoote · 31問 · 1年前

Item 407 Concrete Structures

31問 • 1年前

Plumbing Design and Estimate (by Max Fajardo)

Vaantoote · 22問 · 1年前

Plumbing Design and Estimate (by Max Fajardo)

22問 • 1年前

Principles and Code of Ethics

Vaantoote · 29問 · 1年前

Principles and Code of Ethics

29問 • 1年前

Plumbing Arithmetic Problems 1

Vaantoote · 75問 · 1年前

Plumbing Arithmetic Problems 1

75問 • 1年前