Who is responsible for ensuring that all aircraft maintenance records are kept up to date

Replacing and cleaning of spark plugs and setting of spark plug gap clearance is considered as?(PART IS 5.1.12)

Where would find the recommended statement for recording the approval or dissaproval for return to service of an aircraft after 100 - hour or annual inspection

A special flight permit may be issued for an aircraft that may not currently meet applicable air worthiness requirements but is capable of a safe flight for the purpose of (PCAR 5.4.1.4)

Special repair to structural engine parts by welding, plating, metalizing, or other methods is an example of ( PART IS:5.1.1.2 )

Replacing defetive safety wiring or cotter pins is

An example of power-plant major repair is

Any maintenance operation requiring the opening of cold and hot sections of a turbine is considered

Which is considered to be typical preventive maintenance operations?(PART IS 5.1.1.2)

All philippine registered aircraft used in general aviation shall be re-weighed

All Philippine registered aircraft used for commercial or aerial work operaions shall be re-weighed

Which part off Philippine Civil Aviation Regulation prescribes the requirements for certification of an aircraft and aeronautical components for continuing airworthiness.

Change to the hub design is?

How long does a holder of a certificate issued under 14 CFR Part 65 have notify the authority after any change in permanent mailing address?

Rewinding the field coil of an electrical accessory is an example of?

What is the regulatory definition of preventive maintenance?

An applicant for an AMT license for Powerplant and Airframe rating relying solely on practical experience shall provide documentary evidence of

What is classified as a major repair?

A special flight permit may be issued for an aircraft that may not currently meet applicable airworthiness requirements , but is applicable of safe flight when: 1. Flying the aircraft to a base where repairs, alterations, or maintenance are to be performed or to a point of storage. 2. Delivering or exporting the aircraft. 3. Product flight testing new production aircraft. 4. Evacuating aircraft from areas on impending danger. 5. Conducting customer demonstration flights in new production aircraft that have been completed production like this. Which statements are correct?

No person may schedule a personnel to perform a maintenance task on an aircraft for more than how many consecutive hours of duty?

A certificate or rating issued to an approved maintenance organization is valid for how many year/s from the date of issuance subject to compliance wuth hte AMO procedure manual?

Which state is correct when an aircraft has not been approved for return to service after an annual inspection because of several items requiring minor repair?

Radio equipment installation made in accordance with the Supplemental Type Certificate data require approval for return to service

Who is authorized among the following to perform preventive maintenance, repair or alteration on civil aircraft of the Philippine registry?

Changes of the following type a powerplant or airframe when not listed in the specifications issued by the Land Transportation Office in accordance with the manufacturer, are considered

When can you consider the repair on the following airframe a major repair?

No airframe, powerplant, or appliance which has undergone maintenance, minor repair, or minor alteration may be approved and returned to the service except by one of the following

What does it mean when it is said that a component conforms with a technical standard order?

The restoration of engine mounts to a condition for safe operation after damage is classified as

Replacement of componentd or complete units such as landing heard with parts supplied by the original manufacturer or manufactured in accordance with approved drawings is considered

Which of the following is a portion of the required permanent maintenance record and entry after 100 - hour inspection?

Change in the basic design made in accordance with the "ASSEC" of the air transportation approved recommendation of the " landing gear shock strut" manufacturing or in accordance with ATO airworthiness directives are considered to be

In accordance with the table of sanction under PCAR Part 1, the penalty for "Improperly releasing an aircraft to service" is

Placards required on an aircraft are specified in

Primary responsibility for compliance with Airworthiness Directives lies with the

Check thrust bearing nuts for tightness on newlly overhauled engines at the first 50 - hour inspection following installation. Subsequent inspections on the thrust bearing knots will be made at each third 50 - hour inspection. From the above statement, at what intervals should you check the thrust bearing nuts for tightness.

Suitability for the use of a specific propeller with a particular engine-sirplame combination be determined by reference to what informational source.

1. A Supplemental Type Certificate may be issued to more than one applicant for the same design change, providing each applicant shows compliance with the applicable Airworthiness requirement. 2. An installation of an item manufactured in accordance with the Technical Standard system requires no further approval for installation in a particular aircraft. Regarding the above statements,

Which regulation provides information regarding instrument range markings for an airplane certificated in the normal category ?

The ff. words are an example of what kind of systems in an AD? "Required within the next 25 hours time-in-service after the effective date of this AD, unless already accomplished."

When an airworthy (at the time of sale) aircraft is sold, Worthiness Certificate

The issuance of an Airworthiness Certificate is governed by

An aircraft mechanic is privileged to perform major alterations on U.S. certificated aircraft; however, the work must be done in accordance with FAA-approves technical data before the aircraft can be returned to service. Which is NOT approved data?

The Air Transport Association of America (ATA) Specification No. 100 1. Establishes a standard for the presentation of technical data maintenance manuals. 2. Divides the aircraft into numbered systems and subsystemsnin order to simplify locating maintenance orders. Regarding the above statements

Which of the following are sometimes used as authorization to deviate from an aircraft original type design. 1. FAA Form 337 2. Supplemental Type Certificate 3. Airworthiness Directives 4. Technical Standard Order

The contracting state on whose register is entered

The state that has iurisdiction over the organization responsible for the final assembly of the aircraft engine or propeller.