Engine Check

28問 • 1年前

Lenard Espiritu

通報

問題一覧

Straightening nitrided crankshafts is

Not recommended

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression.

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337.

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets

Indentations on bearing races caused by high static loads are known as

Brinelling

A Cessna 180 aircraft has a McCauley propeller Model No. 2A34C50/90A. The propeller was severely damaged in a ground accident, and this model propeller is not available for replacement. Which of the following should be used to find an approved alternate replacement?

Aircraft Specifications/Type Certificate Data Sheets

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called?

Galling

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD.

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hours total time.

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the '985" indicate?

The total piston displacement of the engine.

Which of the following can inspect and approve an engine major repair for return to service?

Certificated mechanic with inspection authorization.

Which of the following contains a minimum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer's maintenance instructions

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been?

Type certificated.

The breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called

Flaking

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer's maintenance instructions when FAA approved

(1) Airworthiness Directives are Federal Aviation Regulations and must be complied with unless specific exemption is granted. (2) Airworthiness Directives of an emergency nature may require immediate compliance upon receipt. Regarding the above statements,

Both No.1 and No. 2 are true.

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

When inspecting an aircraft reciprocating engine, what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

(1) Serviceability limits for turbine blades are much more stringent than those for turbine nozzle vanes. (2) A limited number of small nicks and dents can usually be permitted in any area of a turbine blade. Regarding the above statement,

Only No.1 is true.

Which of the following is used to monitor the mechanical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done.

What publication is used for guidance to determine whether a powerplant repair is major or minor?

14 CFR Part 43

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer's Service Instructions

How is the flow range of the fuel discharge nozzles installed in a fuel injected reciprocating engine indicated?

By a letter stamped on the hex of the nozzle body

APCAR/ PCAR

Lenard Espiritu · 37問 · 1年前

APCAR/ PCAR

37問 • 1年前

Lenard Espiritu

APCAR/PCAR (Optimized)

Lenard Espiritu · 63問 · 1年前

APCAR/PCAR (Optimized)

63問 • 1年前

Lenard Espiritu

Airframe Check

Lenard Espiritu · 13問 · 1年前

Airframe Check

13問 • 1年前

Lenard Espiritu

Data & Entry

Lenard Espiritu · 37問 · 1年前

Data & Entry

37問 • 1年前

Lenard Espiritu

Docs & Forms

Lenard Espiritu · 37問 · 1年前

Docs & Forms

37問 • 1年前

Lenard Espiritu

Limit and privileges

Lenard Espiritu · 32問 · 1年前

Limit and privileges

32問 • 1年前

Lenard Espiritu

Aircraft Electric Current

Lenard Espiritu · 100問 · 1年前

Aircraft Electric Current

100問 • 1年前

Lenard Espiritu

Aircraft Electrica Current (2)

Lenard Espiritu · 30問 · 1年前

Aircraft Electrica Current (2)

30問 • 1年前

Lenard Espiritu

Aircraft Fitting

Lenard Espiritu · 80問 · 1年前

Aircraft Fitting

80問 • 1年前

Lenard Espiritu

Aircraft Instruments

Lenard Espiritu · 63問 · 1年前

Aircraft Instruments

63問 • 1年前

Lenard Espiritu

Aircraft Structures

Lenard Espiritu · 100問 · 1年前

Aircraft Structures

100問 • 1年前

Lenard Espiritu

Aircraft Structures (2)

Lenard Espiritu · 33問 · 1年前

Aircraft Structures (2)

33問 • 1年前

Lenard Espiritu

Electricity Fundamentals

Lenard Espiritu · 13問 · 1年前

Electricity Fundamentals

13問 • 1年前

Lenard Espiritu

問題一覧

Straightening nitrided crankshafts is

Not recommended

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression.

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337.

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets

Indentations on bearing races caused by high static loads are known as

Brinelling

Aircraft Specifications/Type Certificate Data Sheets

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called?

Galling

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD.

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hours total time.

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the '985" indicate?

The total piston displacement of the engine.

Which of the following can inspect and approve an engine major repair for return to service?

Certificated mechanic with inspection authorization.

Which of the following contains a minimum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer's maintenance instructions

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been?

Type certificated.

The breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called

Flaking

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer's maintenance instructions when FAA approved

Both No.1 and No. 2 are true.

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

When inspecting an aircraft reciprocating engine, what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

Only No.1 is true.

Which of the following is used to monitor the mechanical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done.

What publication is used for guidance to determine whether a powerplant repair is major or minor?

14 CFR Part 43

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer's Service Instructions

How is the flow range of the fuel discharge nozzles installed in a fuel injected reciprocating engine indicated?

By a letter stamped on the hex of the nozzle body