nat sci 3

19問 • 1年前

Dale Cabanlong

通報

問題一覧

Which tool can be used to measure the alignment of a rotor shaft or the plane of rotation of a disk?

dial indicator

Holes and a few projecting globules are found in a weld. What action should be taken?

Remove all the old weld, and Reweld the joint

A particular component is attached to the aircraft structure by the use of an aircraft bolt and a castle tension nut combination. If the cotter pin hole does not align within the recommended torque range, the acceptable practice is to

change the washers and try again

Liquid penetrant inspection methods may be used on which of the following? 1. Porous plastics 2. Ferrous metals 3. Nonferrous metals 4. Smooth primer-sealed wood 5. Nonporous plastics

2,3,5

Why should an aircraft maintenance technician be familiar with weld nomenclature?

In order to gain familiarity with the welding technique, filler material and temperature range

Aircraft bolts with a cross or asterisk marked on the bolthead are

standard steel bolts

Select a characteristics of a good gas weldSelect a characteristics of a good gas weld

The weld should taper off smoothly into the base metal

One way a part may be demagnetized after magnetic particle inspection is by

Slowly moving the part out of an ac magnetic field of sufficient strength

Which tool is used to find the center of a shaft or other cylindrical work

combination set

Normalizing is a process of heat treating

iron based metal only

Under magnetic particle inspection, a part will be identified as having a fatigue crack under which condition?

The discontinuity is found in a highly stressed area of the part

Which of these nondestructive testing methods is suitable for the inspection of most metals, plastics and ceramics for surface and subsurface defects?

ultrasonic inspection

What metal has special short-time heat properties and is used in the construction of aircraft firewalls?

titanium alloy

The reheating of het treated metal, such as with a welding torch

Can significantly alter a metal’s properties in the reheated area

The pattern for an inclusion is a magnetic particle build up forming

parallel lines

In the four-digit aluminum index system number 2024, the first digit indicates

major alloying element

A bolt with a single raised dash on the head is classified as an

AN corrosion-resistant steel bolt

A part which is being prepared for dye penetrant inspection should be clean with

A volatile petroleum-based solvent

What tool is generally used to set a divider to an exact dimension?

machinist scale

human performance

Dale Cabanlong · 33問 · 1年前

human performance

33問 • 1年前

Dale Cabanlong

nat sci

Dale Cabanlong · 31問 · 1年前

nat sci

31問 • 1年前

Dale Cabanlong

nat sci 2

Dale Cabanlong · 35問 · 1年前

nat sci 2

35問 • 1年前

Dale Cabanlong

PCAR

Dale Cabanlong · 23問 · 1年前

PCAR

23問 • 1年前

Dale Cabanlong

PCAR 2nd

Dale Cabanlong · 21問 · 1年前

PCAR 2nd

21問 • 1年前

Dale Cabanlong

PCAR FINAL

Dale Cabanlong · 15問 · 1年前

PCAR FINAL

15問 • 1年前

Dale Cabanlong

AFCAR 1

Dale Cabanlong · 24問 · 1年前

AFCAR 1

24問 • 1年前

Dale Cabanlong

AFCAR 2

Dale Cabanlong · 19問 · 1年前

AFCAR 2

19問 • 1年前

Dale Cabanlong

aircraft fuel systems 1

Dale Cabanlong · 54問 · 1年前

aircraft fuel systems 1

54問 • 1年前

Dale Cabanlong

問題一覧

Which tool can be used to measure the alignment of a rotor shaft or the plane of rotation of a disk?

dial indicator

Holes and a few projecting globules are found in a weld. What action should be taken?

Remove all the old weld, and Reweld the joint

change the washers and try again

Liquid penetrant inspection methods may be used on which of the following? 1. Porous plastics 2. Ferrous metals 3. Nonferrous metals 4. Smooth primer-sealed wood 5. Nonporous plastics

2,3,5

Why should an aircraft maintenance technician be familiar with weld nomenclature?

In order to gain familiarity with the welding technique, filler material and temperature range

Aircraft bolts with a cross or asterisk marked on the bolthead are

standard steel bolts

Select a characteristics of a good gas weldSelect a characteristics of a good gas weld

The weld should taper off smoothly into the base metal

One way a part may be demagnetized after magnetic particle inspection is by

Slowly moving the part out of an ac magnetic field of sufficient strength

Which tool is used to find the center of a shaft or other cylindrical work

combination set

Normalizing is a process of heat treating

iron based metal only

Under magnetic particle inspection, a part will be identified as having a fatigue crack under which condition?

The discontinuity is found in a highly stressed area of the part

Which of these nondestructive testing methods is suitable for the inspection of most metals, plastics and ceramics for surface and subsurface defects?

ultrasonic inspection

What metal has special short-time heat properties and is used in the construction of aircraft firewalls?

titanium alloy

The reheating of het treated metal, such as with a welding torch

Can significantly alter a metal’s properties in the reheated area

The pattern for an inclusion is a magnetic particle build up forming

parallel lines

In the four-digit aluminum index system number 2024, the first digit indicates

major alloying element

A bolt with a single raised dash on the head is classified as an

AN corrosion-resistant steel bolt

A part which is being prepared for dye penetrant inspection should be clean with

A volatile petroleum-based solvent

What tool is generally used to set a divider to an exact dimension?

machinist scale