Engine Check

28問 • 1年前

問題一覧

Which of the following can inspect and approve an engine major repair for return to service?

Certificated mechanic with inspection authorization.

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours' total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hours' total time.

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer's maintenance instructions

When inspecting an aircraft reciprocating engine, what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer's Service Instructions

Which of the following contains a minumum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

On a reciprocating engine aircraft using a shrouded exhaust muffler system as source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done.

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD.

"(1) Serviceability limits for turbine blades are much more stringent than those for turbine nozzle vanes. (2) A limited number of small nicks and dents can usually be permitted in any area of a turbine blade. Regarding the statements,"

Only No. 1 is true

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called?

Galling

Indentations on bearing races caused by high static loads are known as

Brinelling

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been?

Type certificated.

A Cessna 180 aircraft has McCauley propeller Model No. 2A34C50/90A. The propeller was severely damaged in a ground accident, and this model propeller is not available for replacement. Which of the following should be used to find an approved alternate replacement?

Aircraft Specifications/Type Certificate Data Sheets

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression.

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337.

"(1) Airworthiness Directives are Federal Aviation Regulations and must be complied with unless specific exemption is granted. (2) Airworthiness Directives of an emergency naature may require immediate compliance upon receipt. Regarding the statements,"

Both No. 1 and No. 2 is true

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the '985' indicate?

The total piston displacement of the engine.

How is the flow range of the fuel discharge nozzles installed in a fuel injected reciprocating engine indicated?

By a letter stamped on the hex of the nozzle body

What publication is used for guidance to determine whether a powerplant repair is major or minor

14 CFR Part 43

The breaking loose of small pieces of metal from coated surfraces, usually caused by defective plating or excessive loads, is called

Flaking

Which of the following is used to monitor the mechnical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer's maintenance instructions when FAA approved

Straightening nitrided crankshafts is

Not recommended

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets

AFCAR & PCAR

Rev Caap · 37問 · 1年前

AFCAR & PCAR

37問 • 1年前

Rev Caap

AFCAR & PCAR (Optimized)

Rev Caap · 63問 · 1年前

AFCAR & PCAR (Optimized)

Airframe Check

Airframe Check

Data & Entry

Data & Entry

Docs & Forms

Docs & Forms

Limits & Privileges

Limits & Privileges

Human Factor

Human Factor

Human Factors Model

Human Factors Model

Physics Fundamentals

Physics Fundamentals

Parts & Procedures

Parts & Procedures

Basic Math

Basic Math

AVIONICS

Rev Caap · 100問 · 1年前

AVIONICS

AVIONICS 2

AVIONICS 2

問題一覧

Which of the following can inspect and approve an engine major repair for return to service?

Certificated mechanic with inspection authorization.

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours' total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hours' total time.

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer's maintenance instructions

When inspecting an aircraft reciprocating engine, what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer's Service Instructions

Which of the following contains a minumum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

On a reciprocating engine aircraft using a shrouded exhaust muffler system as source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done.

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD.

Only No. 1 is true

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called?

Galling

Indentations on bearing races caused by high static loads are known as

Brinelling

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been?

Type certificated.

Aircraft Specifications/Type Certificate Data Sheets

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression.

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337.

Both No. 1 and No. 2 is true

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the '985' indicate?

The total piston displacement of the engine.

How is the flow range of the fuel discharge nozzles installed in a fuel injected reciprocating engine indicated?

By a letter stamped on the hex of the nozzle body

What publication is used for guidance to determine whether a powerplant repair is major or minor

14 CFR Part 43

The breaking loose of small pieces of metal from coated surfraces, usually caused by defective plating or excessive loads, is called

Flaking

Which of the following is used to monitor the mechnical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer's maintenance instructions when FAA approved

Straightening nitrided crankshafts is

Not recommended

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets