HYDRAULIC PRE FINALS

23問 • 1年前

Nillo Jb

通報

問題一覧

Hydraulic System Components

Reservoir Pump Valves Filter Actuating Mechanism

is a tank in which an adequate supply of fluid for the system is stored.

Reservoir

Are used in aircraft that are not designed for violent maneuvers, do not fly at high altitudes, or in which the reservoir is located in the pressurized area of the aircraft.

Nonpressurized Reservoirs

on aircraft designed for high-altitude flight are usually pressurized. Pressurizing assures a positive flow of fluid to the pump at high altitudes when low atmospheric pressures are encountered.

Pressurized Reservoirs

are the primary source of energy and may be either engine driven, electric motor driven, or air driven.

Power-Driven Pumps

are installed for use in emergencies or during ground operations.

Electrical Motor Pumps

is used in some older aircraft for the operation of hydraulic subsystems and in a few newer aircraft systems as a backup unit.

Hand Pump

Types of Flow Control Valves

Selector Valve Check Valve Sequence Valve Priority Valve Quick Valve

Types of Pressure Control Valves

Relief Valve Pressure Regulator Pressure Reducer

Type of shuttle valve

Shutoff Valve

control the speed and/or direction of fluid flow in the hydraulic system.

Flow Control Valve

It is used to control the direction of movement of a hydraulic actuating cylinder or similar device

Selector Valve

allows fluid to flow unimpeded in one direction but prevents or restricts fluid flow in the opposite direction.

Check Valve

It control the sequence of operation between two branches in a circuit; they enable one unit to automatically set another unit into motion.

Sequence Valve

gives priority to the critical hydraulic subsystems over noncritical systems when system pressure is low.

Priority Valves

are installed in hydraulic lines to prevent loss of fluid when units are removed.

Quick Disconnect Valves

is used to limit the amount of pressure being exerted on a confined liquid. This is necessary to prevent failure of components or rupture of hydraulic lines under excessive pressures.

Relief Valve

is to manage the output of the pump to maintain system operating pressure within a predetermined range.

Pressure Regulator

provide a steady pressure into a system that operates at a lower pressure than the supply system

Pressure Reducer

is to isolate the normal system from an alternate or emergency system.

Shuttle Valve

are used to shut off the flow of fluid to a particular system or component.

Shutoff Valves

is a screening or straining device used to clean the hydraulic fluid, preventing foreign particles and contaminating substances from remaining in the system.

Filter

utilizes an element made of specially treated paper that is formed in vertical convolutions (wrinkles). An internal spring holds the elements in shape.

Micron-Type Filter

BasicElec Pre Final

Nillo Jb · 38問 · 2年前

BasicElec Pre Final

38問 • 2年前

Nillo Jb

basic elec final exam

Nillo Jb · 13問 · 2年前

basic elec final exam

DASURV

DASURV

ComNav prelims

ComNav prelims

Landing Gear System

Landing Gear System

AMT 620 Prelims

AMT 620 Prelims

AMT 626

AMT 626

AMT 627 CABIN ATMOS PRELIM

Nillo Jb · 26問 · 1年前

AMT 627 CABIN ATMOS PRELIM

PowerPlant 2

PowerPlant 2

PATHFIT

PATHFIT

Hydraulic Midterm

Hydraulic Midterm

Landing Gear Midterm

Landing Gear Midterm

ComNav Midterm

ComNav Midterm

ASSEMBLY RIGGING MIDTERM

Nillo Jb · 32問 · 1年前

ASSEMBLY RIGGING MIDTERM

PROPELLER

PROPELLER

RIGGING PRE FINALS

RIGGING PRE FINALS

LandingGear PreFinals

Nillo Jb · 21問 · 1年前

LandingGear PreFinals

ROTC 11General Order

ROTC 11General Order

Midterm Aviation with principle of flight

Nillo Jb · 37問 · 1年前

Midterm Aviation with principle of flight

37問 • 1年前

Nillo Jb

問題一覧

Hydraulic System Components

Reservoir Pump Valves Filter Actuating Mechanism

is a tank in which an adequate supply of fluid for the system is stored.

Reservoir

Are used in aircraft that are not designed for violent maneuvers, do not fly at high altitudes, or in which the reservoir is located in the pressurized area of the aircraft.

Nonpressurized Reservoirs

on aircraft designed for high-altitude flight are usually pressurized. Pressurizing assures a positive flow of fluid to the pump at high altitudes when low atmospheric pressures are encountered.

Pressurized Reservoirs

are the primary source of energy and may be either engine driven, electric motor driven, or air driven.

Power-Driven Pumps

are installed for use in emergencies or during ground operations.

Electrical Motor Pumps

is used in some older aircraft for the operation of hydraulic subsystems and in a few newer aircraft systems as a backup unit.

Hand Pump

Types of Flow Control Valves

Selector Valve Check Valve Sequence Valve Priority Valve Quick Valve

Types of Pressure Control Valves

Relief Valve Pressure Regulator Pressure Reducer

Type of shuttle valve

Shutoff Valve

control the speed and/or direction of fluid flow in the hydraulic system.

Flow Control Valve

It is used to control the direction of movement of a hydraulic actuating cylinder or similar device

Selector Valve

allows fluid to flow unimpeded in one direction but prevents or restricts fluid flow in the opposite direction.

Check Valve

It control the sequence of operation between two branches in a circuit; they enable one unit to automatically set another unit into motion.

Sequence Valve

gives priority to the critical hydraulic subsystems over noncritical systems when system pressure is low.

Priority Valves

are installed in hydraulic lines to prevent loss of fluid when units are removed.

Quick Disconnect Valves

is used to limit the amount of pressure being exerted on a confined liquid. This is necessary to prevent failure of components or rupture of hydraulic lines under excessive pressures.

Relief Valve

is to manage the output of the pump to maintain system operating pressure within a predetermined range.

Pressure Regulator

provide a steady pressure into a system that operates at a lower pressure than the supply system

Pressure Reducer

is to isolate the normal system from an alternate or emergency system.

Shuttle Valve

are used to shut off the flow of fluid to a particular system or component.

Shutoff Valves

is a screening or straining device used to clean the hydraulic fluid, preventing foreign particles and contaminating substances from remaining in the system.

Filter

utilizes an element made of specially treated paper that is formed in vertical convolutions (wrinkles). An internal spring holds the elements in shape.

Micron-Type Filter