TestSkapare

TestSkapare

​
Logga in

c7,4

c7,4
20 frågor • 1 år sedan
  • Aljuboory
    • rapportera

    Frågelista

  • 1

    Current measurements are different from other measurements made with a multimeter in that

    current is measured in series

  • 2

    The display rate of a digital multimeter is:

    the number of time per second that the meter takes a measurement

  • 3

    A 3½-digit meter, can display three full digits ranging from

    0 to 9, and one half digit which displays a 1 or is left blank For example 1,999

  • 4

    the largest allowable error that occurs under specific operating conditions is

    accuracy

  • 5

    Checked AC circuit if it’s open or live AC circuit by

    using Multimeter when set to AC volt

  • 6

    Measurement of electrical current, voltage using digital multimeter the indication is:

    RMS values

  • 7

    If the covers and blanks not remove from pitot probes and static ports before flight may cause Error in:

    airspeed and altitude - sensing

  • 8

    On a static leak tester pressure is released by

    a bleed valve in the tester

  • 9

    Continuity test carried out using

    an Ohmmeter

  • 10

    Checked AC circuit if it’s open or live AC circuit by using Multimeter when set to

    AC volt

  • 11

    A resistor that is placed in series with the meter movement is called

    a multiplier resistor

  • 12

    An ammeter, its coil has relatively

    few turns of heavy wire

  • 13

    Some earlier cable constructions tended to exhibit ‘knuckling of conductors which could be severe enough to penetrate the insulation. This was induced by applying

    excessive pull through forces

  • 14

    Continuity testing

    to find a high resistance or open circuit carries out

  • 15

    What type of check is used to find high resistance or open circuit on a cable assembly?

    a continuity check

  • 16

    Voltage Measurement

    Voltage (E) = Current (I) x Resistance (R)

  • 17

    Any ohmmeter used for measuring insulation resistance must be used in association with a source of supply having an output voltage that is at least

    equal to or higher than the working voltage

  • 18

    Ensure that the equipment or conductor to be tested is

    de-energized before connecting the instrument

  • 19

    Before using a bonding tester the 6 foot leads has the two prongs shorted together what would the indicator read?

    Full scale right

  • 20

    This type of movement is its cheapness and it may be used in

    both AC and DC

    • mod 4 test

    mod 4 test

    Aljuboory · 81 frågor · 1 år sedan

    mod 4 test

    mod 4 test

    81 frågor • 1 år sedan
    Aljuboory

    mod 2 test

    mod 2 test

    Aljuboory · 100 frågor · 1 år sedan

    mod 2 test

    mod 2 test

    100 frågor • 1 år sedan
    Aljuboory

    mod 2,2

    mod 2,2

    Aljuboory · 94 frågor · 1 år sedan

    mod 2,2

    mod 2,2

    94 frågor • 1 år sedan
    Aljuboory

    mod 6,1

    mod 6,1

    Aljuboory · 277 frågor · 1 år sedan

    mod 6,1

    mod 6,1

    277 frågor • 1 år sedan
    Aljuboory

    c7.1

    c7.1

    Aljuboory · 18 frågor · 1 år sedan

    c7.1

    c7.1

    18 frågor • 1 år sedan
    Aljuboory

    c7.2

    c7.2

    Aljuboory · 11 frågor · 1 år sedan

    c7.2

    c7.2

    11 frågor • 1 år sedan
    Aljuboory

    c7.3

    c7.3

    Aljuboory · 36 frågor · 1 år sedan

    c7.3

    c7.3

    36 frågor • 1 år sedan
    Aljuboory

    c7.5

    c7.5

    Aljuboory · 11 frågor · 1 år sedan

    c7.5

    c7.5

    11 frågor • 1 år sedan
    Aljuboory

    c7.7

    c7.7

    Aljuboory · 17 frågor · 1 år sedan

    c7.7

    c7.7

    17 frågor • 1 år sedan
    Aljuboory

    c7.8

    c7.8

    Aljuboory · 5 frågor · 1 år sedan

    c7.8

    c7.8

    5 frågor • 1 år sedan
    Aljuboory

    c7.9

    c7.9

    Aljuboory · 8 frågor · 1 år sedan

    c7.9

    c7.9

    8 frågor • 1 år sedan
    Aljuboory

    7.10

    7.10

    Aljuboory · 12 frågor · 1 år sedan

    7.10

    7.10

    12 frågor • 1 år sedan
    Aljuboory

    c7.11

    c7.11

    Aljuboory · 6 frågor · 1 år sedan

    c7.11

    c7.11

    6 frågor • 1 år sedan
    Aljuboory

    c7.12

    c7.12

    Aljuboory · 10 frågor · 1 år sedan

    c7.12

    c7.12

    10 frågor • 1 år sedan
    Aljuboory

    c7.13

    c7.13

    Aljuboory · 10 frågor · 1 år sedan

    c7.13

    c7.13

    10 frågor • 1 år sedan
    Aljuboory

    c7.14

    c7.14

    Aljuboory · 17 frågor · 1 år sedan

    c7.14

    c7.14

    17 frågor • 1 år sedan
    Aljuboory

    c7.15

    c7.15

    Aljuboory · 20 frågor · 1 år sedan

    c7.15

    c7.15

    20 frågor • 1 år sedan
    Aljuboory

    c7.16

    c7.16

    Aljuboory · 14 frågor · 1 år sedan

    c7.16

    c7.16

    14 frågor • 1 år sedan
    Aljuboory

    c7.17

    c7.17

    Aljuboory · 14 frågor · 1 år sedan

    c7.17

    c7.17

    14 frågor • 1 år sedan
    Aljuboory

    c7.18

    c7.18

    Aljuboory · 36 frågor · 1 år sedan

    c7.18

    c7.18

    36 frågor • 1 år sedan
    Aljuboory

    c7.19

    c7.19

    Aljuboory · 11 frågor · 1 år sedan

    c7.19

    c7.19

    11 frågor • 1 år sedan
    Aljuboory

    c7.20

    c7.20

    Aljuboory · 18 frågor · 1 år sedan

    c7.20

    c7.20

    18 frågor • 1 år sedan
    Aljuboory

    Frågelista

  • 1

    Current measurements are different from other measurements made with a multimeter in that

    current is measured in series

  • 2

    The display rate of a digital multimeter is:

    the number of time per second that the meter takes a measurement

  • 3

    A 3½-digit meter, can display three full digits ranging from

    0 to 9, and one half digit which displays a 1 or is left blank For example 1,999

  • 4

    the largest allowable error that occurs under specific operating conditions is

    accuracy

  • 5

    Checked AC circuit if it’s open or live AC circuit by

    using Multimeter when set to AC volt

  • 6

    Measurement of electrical current, voltage using digital multimeter the indication is:

    RMS values

  • 7

    If the covers and blanks not remove from pitot probes and static ports before flight may cause Error in:

    airspeed and altitude - sensing

  • 8

    On a static leak tester pressure is released by

    a bleed valve in the tester

  • 9

    Continuity test carried out using

    an Ohmmeter

  • 10

    Checked AC circuit if it’s open or live AC circuit by using Multimeter when set to

    AC volt

  • 11

    A resistor that is placed in series with the meter movement is called

    a multiplier resistor

  • 12

    An ammeter, its coil has relatively

    few turns of heavy wire

  • 13

    Some earlier cable constructions tended to exhibit ‘knuckling of conductors which could be severe enough to penetrate the insulation. This was induced by applying

    excessive pull through forces

  • 14

    Continuity testing

    to find a high resistance or open circuit carries out

  • 15

    What type of check is used to find high resistance or open circuit on a cable assembly?

    a continuity check

  • 16

    Voltage Measurement

    Voltage (E) = Current (I) x Resistance (R)

  • 17

    Any ohmmeter used for measuring insulation resistance must be used in association with a source of supply having an output voltage that is at least

    equal to or higher than the working voltage

  • 18

    Ensure that the equipment or conductor to be tested is

    de-energized before connecting the instrument

  • 19

    Before using a bonding tester the 6 foot leads has the two prongs shorted together what would the indicator read?

    Full scale right

  • 20

    This type of movement is its cheapness and it may be used in

    both AC and DC