記憶度
4問
11問
0問
0問
0問
アカウント登録して、解答結果を保存しよう
問題一覧
1
Which of the following indications occur during a normal operational check of a pneumatic deicer system?
Fluctuating readings on the pressure gauge and relatively steady readings on the vacuum gauge
2
What is used as temperature-sensing element in an electrically heated windshield?
Thermistor
3
Which of the following connects vacuum to the deicer boots when the system is not in operation, to hold the boots tightly against the leading edges in flight?
Distributor valve
4
Carburetor icing may be eliminated by which of the following methods?
Alcohol spray and heated induction air
5
Two possible source of heat for the operation of a wing thermal anti-icing systems are
Compressor bleed air and aircraft electrical system
6
Arcing in an electrically heated windshield panel usually indicates a breakdown in the
Conductive coating
7
Which of the following is the best means to use when removing wet snow from an aircraft?
A brush or a squeegee
8
Some aircraft are protected against airframe icing by heating the leading edges of the airfoils and intake ducts. When is this type of anti-ice system usually operated during flight?
Whenever icing conditions are first encountered or expected to occur
9
Where are the heat sensors located on most aircraft with electrically heated windshields?
Imbedded in the glass
10
How do deicer boots help remove ice accumulation?
By breaking up ice formation
11
What is the purpose of the oil separator in the pneumatic deicing system?
To protect the deicer boots from oil deterioration
12
What should be used to melt the ice in a turbine engine if the compressor is immobile because of ice?
Hot air
13
What are three methods of anti-icing aircraft windshields? 1. Blanket-type heating system 2. An electric heating element in the windshield 3. Heated air circulating system 4. Hot water system 5. Windshield wipers and anti-icing fluid 6. Ribbon-type heating system
2,3,5
14
What icing condition may occur when there is no visible moisture present?
Carburetor ice
15
Which of the following regulates the vacuum of the air pump to hold the deising boots deflated when the pneumatic deicing sysytem in off?
Suction relief valve
16
What is the purpose of the distributor valve in a deicing system utilizing deicer boots?
To sequence the deicer boots inflations symmetrically
17
What controls the inflation sequence in a pneumatic deicer boot system?
Distributor valve
18
What may be used to clean deicer boots?
Soap and water
19
What mixture may be used as a deicing fluid to remove frost from an aircraft surface?
Ethylene glycol and isopropyl alcohol
20
Why are the tubes in deicer boots alternately inflated?
Alternate inflation of deicer boot tubes keeps disturbance of the airflow to a minimum
21
What maintains normal windshield temperature control in an electrically heated windshield system?
Thermistors
22
What method is usually employed to control the temperature of an anti-icing system using surface combustion heaters?
Thermo-cycling switches
23
Prior to installation of a pneumatic surface-bonded type deicer boots, on the leading edge of the wing, you should
Remove all paint from the area to be covered by the deicer boot
24
What is the principle characteristics of a windshield pneumatic rain removal system?
An air blast forms a barrier that prevents raindrops from striking the windshield surface
25
What is the source of pressure for inflating deicer boots on reciprocating engine aircraft?
Vane-type pump
26
What is one check for proper operation of a pilot/static tube heater after replacement?
Ammeter reading
27
Why should a chemical rain repellant not be used on a dry windshield?
It will restrict visibility
28
Which of the following are found in laminated integral electrically heated windshield system? 1. Autotransformer 2. Heat control relay 3. Heat control toggle switch 4. 24v dc power supply 5. Indicating light
1,2,3,5