Aicraft Maintenance Engine Inspection

29問 • 1年前

問題一覧

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done

When inspecting an aircraft reciprocating engine what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

(1) Serviceability limits for turbine blades are much more stringent than are those for turbine nozzle vanes. (2) A limited number of small nicks and dents can usually be permitted in any area of a turbine blade. Regarding above statements,

Only no. 1 is true

Which of the following can inspect and approve an engine major repair for return to service?

Certified mechanic with inspection authorization

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called

Galling

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the ‘985’ indicate?

The total piston displacement of the engine

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer’s maintenance instruction when FAA approved

(1) Airworthiness Directives are Federal Aviation Regulations and must be complied with unless specific exemption is granted. (2) Airworthiness Directives of an emergency nature may require immediate compliance upon receipt. Regarding the above statements,

Both no.1 and no.2 are true

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours’ total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hour’s total time

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets

Indentations on bearing races caused by high static loads are known as

Brinelling

What publication is used for guidance to determine whether a powerplant repair is major or minor?

Federal Aviation Regulations, Part 43, appendix A.

Determine which portion of the AD is applicable for Model 0-690 series engine, serial No. 5863-40 with 283 hours’ time in service. This is the compliance portion of an FAA Airworthiness Directive. Compliance required as indicated: (A) For model 0-690 series engines, serial Nos. 101-40 through 5264-40 and IO-690 series engines, serial Nos. 101-48 through 423-48, compliance with (c) Required within 25 hours’ time in service after the effective date of this AD and every 100 hours’ time in service thereafter. (B) For model O-690 series engines, serial Nos. 5265-40 through 6129-40 and IO-690 series engines, serial Nos. 424-48 through 551-48, compliance with (C)required as follows: (1) Within 25 hours’ time in service after the effective date of this AD and every 100 hours’ time in service thereafter for engines with more than 275 hours’ time in service on the effective date of this AD. (2) Prior to the accumulation of 300 hours total time in service and every 100 hours’ time in service thereafter for engines with 275hours or less time in service on the effective date of this AD. (C) Inspect the oil pump drive shaft (P/N 67512) on applicable engines in accordance with instructions contained in Connin Service Bulletin No. 295. Any shafts which are found to be damaged shall be replaced before further flight. These inspections shall be continued until Connin P/N 67512 (redesigned) or P/n 74641 oil pump drive shaft is installed at which time the inspections may be discontinued.

(B), (1)

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

Which of the following contains a minimum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been

Type certificated

A Cessna 180 aircraft has a McCauley propeller Model No. 2A34C50/90A.The propeller severely damaged in a ground accident, and this model propeller is not available for replacement. Which of the following should be used to find an approved alternate replacement?

Aircraft Specifications/ Type Certificate Data Sheets

The breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called

Flaking

How are discharge nozzles in a fuel injected reciprocating engine identified to indicate the flow range?

By an identification letter stamped on one of the hexes of the nozzle body

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer’s maintenance instructions

Which of the following is used to monitor the mechanical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

Straightening nitride crankshaft is

Not recommended

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer’s service instructions

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression

Airframe Wood Structure

AR Ramos · 16問 · 1年前

Airframe Wood Structure

16問 • 1年前

AR Ramos

Airframe Aircraft Finishes

AR Ramos · 15問 · 1年前

Airframe Aircraft Finishes

15問 • 1年前

AR Ramos

Airframe Aircraft Covering

AR Ramos · 12問 · 1年前

Airframe Aircraft Covering

12問 • 1年前

AR Ramos

Airframe Ice & Rain Control Systems

AR Ramos · 28問 · 1年前

Airframe Ice & Rain Control Systems

28問 • 1年前

AR Ramos

Aircraft Fire Extinguishing System

AR Ramos · 30問 · 1年前

Aircraft Fire Extinguishing System

30問 • 1年前

AR Ramos

Airframe Aircraft Position And Warning System

AR Ramos · 35問 · 1年前

Airframe Aircraft Position And Warning System

35問 • 1年前

AR Ramos

Aircraft Maintenance Ground Operation & Servicing

AR Ramos · 38問 · 1年前

Aircraft Maintenance Ground Operation & Servicing

38問 • 1年前

AR Ramos

Aircraft Maintenance Fluid Lines & Fitting

AR Ramos · 35問 · 1年前

Aircraft Maintenance Fluid Lines & Fitting

35問 • 1年前

AR Ramos

Aircraft Maintenance Cleaning & Corrosion Control

AR Ramos · 34問 · 1年前

Aircraft Maintenance Cleaning & Corrosion Control

34問 • 1年前

AR Ramos

問題一覧

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be

Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done

When inspecting an aircraft reciprocating engine what document is used to determine if the proper magnetos are installed?

Aircraft Engine Specifications or Type Certificate Data Sheets.

Only no. 1 is true

Which of the following can inspect and approve an engine major repair for return to service?

Certified mechanic with inspection authorization

A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called

Galling

You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the ‘985’ indicate?

The total piston displacement of the engine

Which of the following contains approved data for performing a major repair to an aircraft engine?

Manufacturer’s maintenance instruction when FAA approved

Both no.1 and no.2 are true

Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours’ total time and 300 hours since rebuilding.

Applies to all IVO-355 engines, serial numbers T8000 through T8300, having less than 2,400 hour’s total time

Which of the following contains a table that lists the engines to which a given propeller is adaptable?

Propeller Type Certificate Data Sheets

Indentations on bearing races caused by high static loads are known as

Brinelling

What publication is used for guidance to determine whether a powerplant repair is major or minor?

Federal Aviation Regulations, Part 43, appendix A.

(B), (1)

What maintenance record(s) is/are required following a major repair of an aircraft engine?

Entries in the engine maintenance record and FAA Form 337

What section in the instructions for continued airworthiness is FAA approved?

Airworthiness limitations section

Which of the following contains a minimum checklist for 100-hour inspections of engines?

14 CFR Part 43 Appendix D

Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been

Type certificated

Aircraft Specifications/ Type Certificate Data Sheets

The breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called

Flaking

How are discharge nozzles in a fuel injected reciprocating engine identified to indicate the flow range?

By an identification letter stamped on one of the hexes of the nozzle body

A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?

Current manufacturer’s maintenance instructions

Which of the following is used to monitor the mechanical integrity of the turbines, as well as to check engine operating conditions of a turbine engine?

Exhaust gas temperature

When must an Airworthiness Directive (AD) be complied with after it becomes effective?

As specified in the AD

Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?

The Aircraft Engine Specifications

The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the

Federal Aviation Regulations, Part 23

Which of the following conditions is usually not acceptable to any extent in turbine blades?

Cracks

Straightening nitride crankshaft is

Not recommended

What publication contains the mandatory replacement time for parts of a turbine engine?

Engine Manufacturer’s service instructions

Which of the following component inspections is to be accomplished on a 100-hour inspection?

Check cylinder compression