130. How do you control freshwater heating temperature in the evaporator side of a Fresh Water Generator?

139. Increasing the speed of a centrifugal pump will result in an increase in the pump capacity. Another means of increasing the total head pressure of a centrifugal pump is to increase the ?

178. One of the routine tasks onboard maintenance for Gas Turbine is mainly of daily visual checks of the running engine. What are you going to execute after a fix number of operating hours to remove any salt deposits on the compressor?

159. Visual inspection of a fuel injector valve, removed during overhaul, shows heat discoloration of the lower end of the valve. This is an indication of

109. Movement of the pump control rack in a fuel injection system having individual plunger-type pumps ?

106. The temperature of the refrigerant in the evaporator coil defends mostly upon the

165. The function of seal cages, or lantern rings installed in the centrifugal pump stuffing boxes, is to

135. What causes carbon deposits in the fuel heater?

152. Gas turbine uses a cycle that includes intake, compression, expansion and exhaust. Which of the following are you going to use to best explain the complete cycle.

137. While overhauling a jerk-type pump and the pump plunger must be replaced. What other part must also be replaced?

107. Which combination of the main shaft segments listed below, that are located furthest from the main engine are connected by the inboard stern tube shaft coupling?

134. One of the routine tasks onboard maintenance for Gas Turbine is mainly of daily visual checks of the running engine. What are you going to execute after a fix number of operating hours to remove any salt deposits on the compressor?

116. What is the characteristic of a one ton air conditioning system?

138. During injection, the cam nose of the camshaft will push up the plunger of the pump, forcing the fuel to the ?

181. In a main propulsion turbine installation, the condensate pump initially discharges to the

175. Main component of the engine to regulate speed is the ?

158. Labyrinth seals used to reduce leakage around a turbine shaft are constructed of

155. Why is thin tipping design procedure is used in modern reaction turbines ?

182. If a reciprocating air compressor has a knock occurring in frequency with its operating RPM, the cause is probably

112. The firing rate of boiler using steam atomization is indicated by the ?

146. The possible cause why lube oil pumps fail to build up discharge pressure could be that the ?

190. Main engine lube oil sump tank is located ?

103. To keep the movement of the rudder closely in step with the steering wheel, which of the devices listed, when used on an electro-hydraulic steering gear?

128. If the fixed orifice in the evaporator steam supply line were to be removed, the steam pressure reducing valve located upstream would

133. What part of the boiler provides water circulation to the waterwall tubes?

104. The capacity of a rotary pump, when operated at a constant speed, will decrease with an increase in the pump?

160. An internally mixed steam atomizer requires which of the following compared to a return flow oil burner system?

186. The capacity of a rotary pump, delivering a constant viscosity fluid, will decrease when the discharge pressure is increased, due to ?

188. Which of the following statement is correct when a piston is said to be at top dead center?

172. In the boilerás combustion control system, when the demand for steam is increased

110. What is the importance of the control box of a differential gear system in a steering gear system?.

176. Movement of the pump control rack in a fuel injection system having individual plunger-type pumps

193. Why diesel engine lubricating oil need more purification compare with the lubricating oil in a gas turbine?

145. In an engine operation what is the effect called that describes the unstable operation of the governor that will not maintain a steady state condition ?

142. How does a quick closing valve operate?

105. Fluctuations in the pressure and temperature of the steam supplied to the first-effect of a low pressure submerged tube distilling plant will cause

118. Cylinder oil is used for ?

102. A salinity indicating system functions on the basic principle of measuring the

150. What type of pump is used in the steering gear of modern ship?

170. Which of the following is the result of excessively high fuel oil temperature ?

194. Which of the following is the reason for installing settling tanks in the fuel oil system?

166. An oil mist detector is used to detect an oil mist formation in the diesel engine crankcase. Which of the following causes oil mist formation ?

148. How many fuel oil heaters are required for main engine operation ?

117. The dehydrator of a refrigeration system is located ?

198. Which of the following terms is used to identify the pressure of the liquid ?

141. The greatest decrease in the temperature of a refrigerant is at the

167. The bore of a diesel engine describes the ?

147. Which of the following statement is correct relative to distillation plant operation?

189. The purpose of the six-way valve used in an electro-hydraulic steering system is to

183. The range of values around a set point of a measured variable where "no action"occurs in an automatic flow controller is called:

179. Boiler safety valves are set not to go above maximum operating pressure of higher than ?.

136. What is the cause of excessively low air pressure occurring in the intercooler of a reciprocating air compressor?

149. Some engines are using auxiliary electrically driven blowers which is continuously running during maneuvering and automatically cut-off if the scavenge air pressure reaches load.

151. What is the possible cause of fuel oil accumulation in boiler casing is ?

140. Which of the following component is the primary shaft emerging out of the engine?lt directly receives the rotational motion from the crankshaft and rotates at the maximum velocity in high speed engines.

184. Passages are drilled at the diesel engine crankshaft in order to provide lubricating oil in the ?.

108. A distorted spray pattern from a fuel injector can cause a diesel engine to have ?

195. Why is it necessary to transfer fuel oil to the settling tanks ?

122. The function of a centrifugal pump double volute casing is to ?

174. What is the purpose of the dehydrator in refrigeration?

154. Most of the fuel injection pumps will then closed after injection because they are fitted with a ?

144. How is viscosity of fuel in the atomizer can be reduced ?

111. Which of the following component is the primary shaft emerging out of the engine. It directly receives the rotational motion from the crankshaft and rotates at the maximum velocity in high-speed engines.

192. When turbine rotor shafts extend through the casing, an external source of sealing steam is used in conjunction with labyrinth packing to.

120. Strainer is commonly used in hydraulic system in order to ?

125. Which of vthe following is the primary purpose of heaters in a pressurized fuel oil system?

115. If the flow of water from the centrifugal pump is allowed to be stopped by closing the discharge valve while the pump continues to run for an extended period, which of the following will occur?

156. In a refrigeration system, the amount of superheat absorbed by the refrigerant is adjusted at the

191. What is the most important rule for the safe operation of a boiler?

119. The average pressure exerted on a piston during each power stroke is termed

168. How is constant steam pressure maintained?

129. What action would you take to perform the most important rule for the safe operation of a boiler?

124. What precaution should be observed to prevent damage of the service pump when warming up the fuel system to the boiler is to ?

169. How will you know the firing rate of boiler using steam atomization indicated?

163. Parts of the pump used to maintain the alignment of the pump are ?

153. Which of the following determines the measured gap between the face of the burner atomizer tip nut and the diffuser plate ?

143. If the boiler fires are extinguished by water contamination in the fuel oil, you should FIRST?

197. Which of the items listed below is normally describe a ventilating fan?

196. Part of centrifugal disc purifier use to hold discs in place and directs the flow of dirty liquid to the bottom then to the discs as the oil flows upward is called

164. A squeaking sound occurring from within an operating reciprocating air compressor is an indication of ?

187. The measure of the amount of salt present in water is called ?

177. Most fuel injection nozzles are opened by ?

157. If turbine rotor shafts extend through the casing, what external source of sealing steam is used in conjunction with labrynith packing ?.

127. Prior to starting, the purpose of turning over a main propulsion diesel engine with the cylinder test cocks open, is to ?

173. The purpose of the diffuser in a boiler burner assembly is to

126. Which of the following would result if the temperature of the fuel to the burners is too low?

131. Inspection of a low pressure gear pump for cavitation will usually be indicated by a wear pattern ?

113. Which of the following cases listed below should soot blowing be applied to avoid soot fires ?

162. Which of the listed conditions is responsible for causing the gland leak off steam from a propulsion turbine to pass through the gland exhaust condenser?

161. What is the reason why fuel is heated before atomizing is to ?

101. Air leaking into a flash type distilling plant could occur through

185. If you hear a crackling sound coming from a salt water centrifugal pump casing, the most probable cause of the noise would be ?

171. Which equipment must be tested NOT more than 12 hours prior to getting underway from a port when the voyage is to be of 48 hours or greater duration?

114. What is the use of a steam control valves installed in the auxiliary exhaust line?

180. Why should hydraulic cranes be properly warmed-up before they are used?

200. Irregular feeding or surging of the feedwater supply to a low pressure distilling plant may be attributed to

123. Distortion of the spray pattern of a nozzle or injector maybe indicated by alarm ?

121. The working principle of an engine is the conversion of ?

199. If you were operating a centrifugal water service pump with worn wearing rings, the

132. Integral water jacket liners use O-rings near the bottom of the liner. These O-rings serve to ?