c7.2

11問 • 1年前

Aljuboory

通報

問題一覧

Control of tools is important to good engineering practices. Tools are normally controlled using:

either the shadow board or the tool tag systems

From an aviation point of view, the most important tool check of all is

the final end of work tool check

CEN is

an European committee for standardization

Basic size:

The theoretical size from which limits of size are derived by the use of tolerances

Allowance :

The minimum clearance space (or maximum interference ) intended between the maximum material conditions of mating parts.

Nominal size:

is an approximate dimension that is used for the purpose of general identification.

The responsibility for insuring that any tool used in aircraft maintenance is serviceable and fit for purpose, rests with the

engineer using the tool

Many of the wide variety of materials, used in workshops, require some form of control in their handling. This control can involve:

Safety, management and economy

(PAS) means :

Publicly available standards

The type of fit that is most suited to the accurate location of mating parts is :

transition fit

One of the information included in the calibration records or certificates is:

limits of permissible error

mod 4 test

Aljuboory · 81問 · 1年前

mod 4 test

81問 • 1年前

Aljuboory

mod 2 test

Aljuboory · 100問 · 1年前

mod 2 test

100問 • 1年前

Aljuboory

mod 2,2

Aljuboory · 94問 · 1年前

mod 2,2

94問 • 1年前

Aljuboory

mod 6,1

Aljuboory · 277問 · 1年前

mod 6,1

277問 • 1年前

Aljuboory

c7.1

Aljuboory · 18問 · 1年前

c7.1

18問 • 1年前

Aljuboory

c7.3

Aljuboory · 36問 · 1年前

c7.3

36問 • 1年前

Aljuboory

c7,4

Aljuboory · 20問 · 1年前

c7,4

20問 • 1年前

Aljuboory

c7.5

Aljuboory · 11問 · 1年前

c7.5

11問 • 1年前

Aljuboory

c7.7

Aljuboory · 17問 · 1年前

c7.7

c7.8

c7.8

c7.9

c7.9

7.10

Aljuboory · 12問 · 1年前

7.10

c7.11

c7.11

c7.12

Aljuboory · 10問 · 1年前

c7.12

10問 • 1年前

Aljuboory

c7.13

Aljuboory · 10問 · 1年前

c7.13

10問 • 1年前

Aljuboory

c7.14

Aljuboory · 17問 · 1年前

c7.14

17問 • 1年前

Aljuboory

c7.15

Aljuboory · 20問 · 1年前

c7.15

20問 • 1年前

Aljuboory

c7.16

Aljuboory · 14問 · 1年前

c7.16

14問 • 1年前

Aljuboory

c7.17

Aljuboory · 14問 · 1年前

c7.17

14問 • 1年前

Aljuboory

c7.18

Aljuboory · 36問 · 1年前

c7.18

36問 • 1年前

Aljuboory

c7.19

Aljuboory · 11問 · 1年前

c7.19

11問 • 1年前

Aljuboory

c7.20

Aljuboory · 18問 · 1年前

c7.20

18問 • 1年前

Aljuboory

問題一覧

Control of tools is important to good engineering practices. Tools are normally controlled using:

either the shadow board or the tool tag systems

From an aviation point of view, the most important tool check of all is

the final end of work tool check

CEN is

an European committee for standardization

Basic size:

The theoretical size from which limits of size are derived by the use of tolerances

Allowance :

The minimum clearance space (or maximum interference ) intended between the maximum material conditions of mating parts.

Nominal size:

is an approximate dimension that is used for the purpose of general identification.

The responsibility for insuring that any tool used in aircraft maintenance is serviceable and fit for purpose, rests with the

engineer using the tool

Many of the wide variety of materials, used in workshops, require some form of control in their handling. This control can involve:

Safety, management and economy

(PAS) means :

Publicly available standards

The type of fit that is most suited to the accurate location of mating parts is :

transition fit

One of the information included in the calibration records or certificates is:

limits of permissible error