c7.13

10問 • 1年前

問題一覧

Check for broken wires

Rub a cloth (rag) along the length of the cable in both directions, do not use bare hands as serious laceration can occur

HTS aircraft control cable are protected from corrosion

be Galvanizing

After swaging an end fitting onto a control cable, a visual inspection for cracks and distortion is performed and then the cable is proof loaded to

50% of the minimum breaking loud for British specification cables and 60% for American specification cables

A control cable is proof loaded to ensure

the end fitting on the cable are secure

It has a set of risers. The tensiometer chart identifies which riser is to be used with each cable size.

Fit the correct riser and correct chart to the tensiometer

Checking for cable tension for

looking for full and free movement

Swaging of cable end fitting is checked by

using a go no go gauge on the barrel

Note : wet arc tracking is a fault caused

by insulation damage

A cable should be replaced when individual wires

are worn greater than 40%

The check for a cable pulling out of a swaged fitting is by looking for

a shiny surface on the cable near the fitting

mod 4 test

Aljuboory · 81問 · 1年前

mod 4 test

81問 • 1年前

Aljuboory

mod 2 test

Aljuboory · 100問 · 1年前

mod 2 test

100問 • 1年前

Aljuboory

mod 2,2

Aljuboory · 94問 · 1年前

mod 2,2

94問 • 1年前

Aljuboory

mod 6,1

Aljuboory · 277問 · 1年前

mod 6,1

277問 • 1年前

Aljuboory

c7.1

Aljuboory · 18問 · 1年前

c7.1

18問 • 1年前

Aljuboory

c7.2

Aljuboory · 11問 · 1年前

c7.2

11問 • 1年前

Aljuboory

c7.3

Aljuboory · 36問 · 1年前

c7.3

36問 • 1年前

Aljuboory

c7,4

Aljuboory · 20問 · 1年前

c7,4

20問 • 1年前

Aljuboory

c7.5

Aljuboory · 11問 · 1年前

c7.5

11問 • 1年前

Aljuboory

c7.7

Aljuboory · 17問 · 1年前

c7.7

c7.8

c7.8

c7.9

c7.9

7.10

Aljuboory · 12問 · 1年前

7.10

c7.11

c7.11

c7.12

Aljuboory · 10問 · 1年前

c7.12

10問 • 1年前

Aljuboory

c7.14

Aljuboory · 17問 · 1年前

c7.14

17問 • 1年前

Aljuboory

c7.15

Aljuboory · 20問 · 1年前

c7.15

20問 • 1年前

Aljuboory

c7.16

Aljuboory · 14問 · 1年前

c7.16

14問 • 1年前

Aljuboory

c7.17

Aljuboory · 14問 · 1年前

c7.17

14問 • 1年前

Aljuboory

c7.18

Aljuboory · 36問 · 1年前

c7.18

36問 • 1年前

Aljuboory

c7.19

Aljuboory · 11問 · 1年前

c7.19

11問 • 1年前

Aljuboory

c7.20

Aljuboory · 18問 · 1年前

c7.20

18問 • 1年前

Aljuboory

問題一覧

Check for broken wires

Rub a cloth (rag) along the length of the cable in both directions, do not use bare hands as serious laceration can occur

HTS aircraft control cable are protected from corrosion

be Galvanizing

After swaging an end fitting onto a control cable, a visual inspection for cracks and distortion is performed and then the cable is proof loaded to

50% of the minimum breaking loud for British specification cables and 60% for American specification cables

A control cable is proof loaded to ensure

the end fitting on the cable are secure

It has a set of risers. The tensiometer chart identifies which riser is to be used with each cable size.

Fit the correct riser and correct chart to the tensiometer

Checking for cable tension for

looking for full and free movement

Swaging of cable end fitting is checked by

using a go no go gauge on the barrel

Note : wet arc tracking is a fault caused

by insulation damage

A cable should be replaced when individual wires

are worn greater than 40%

The check for a cable pulling out of a swaged fitting is by looking for

a shiny surface on the cable near the fitting