4

10 questions • 2024-05-14
Alexandra Svobodová
Report

Question

What are two common causes of signal degradation when using UTP cabling? (Choose two.)

  • installing cables in conduit

  • low-quality shielding in cable

  • loss of light over long distances

  • low-quality cable or connectors

  • improper termination

Question

Which scenario describes a function provided by the transport layer?

  • A student is playing a short web-based movie with sound. The movie and sound are encoded within the transport layer header.

  • A corporate worker is accessing a web server located on a corporate network. The transport layer formats the screen so the web page appears properly no matter what device is being used to view the web site.

  • A student has two web browser windows open in order to access two web sites. The transport layer ensures the correct web page is delivered to the correct browser window.

  • A student is using a classroom VoIP phone to call home. The unique identifier burned into the phone is a transport layer address used to contact another network device on the same network.

  • Skip

Question

Which two protocols operate at the top layer of the TCP/IP protocol suite? (Choose two.)

  • UDP

  • IP

  • Ethernet

  • TCP

  • POP

  • DNS

Question

An employee of a large corporation remotely logs into the company using the appropriate username and password. The employee is attending an important video conference with a customer concerning a large sale. It is important for the video quality to be excellent during the meeting. The employee is unaware that after a successful login, the connection to the company ISP failed. The secondary connection, however, activated within seconds. The disruption was not noticed by the employee or other employees. What three network characteristics are described in this scenario? (Choose three.)

  • security

  • scalability

  • integrity

  • quality of service

  • powerline networking

  • fault tolerance

Question

Refer to the exhibit. If PC1 is sending a packet to PC2 and routing has been configured between the two routers, what will R1 do with the Ethernet frame header attached by PC1?

  • open the header and replace the destination MAC address with a new one

  • open the header and use it to determine whether the data is to be sent out S0/0/0

  • nothing, because the router has a route to the destination network

  • remove the Ethernet header and configure a new Layer 2 header before sending it out S0/0/0

  • Skip

Question

Which three layers of the OSI model map to the application layer of the TCP/IP model? (Choose three.)

  • application

  • session

  • data link

  • presentation

  • transport

  • network

  • nn

  • ok

  • Skip

Question

What does the term “attenuation” mean in data communication?

  • loss of signal strength as distance increases

  • strengthening of a signal by a networking device

  • time for a signal to reach its destination

  • leakage of signals from one cable pair to another

  • Skip

Question

Which two statements describe how to assess traffic flow patterns and network traffic types using a protocol analyzer? (Choose two.)

  • Only capture traffic in the areas of the network that receive most of the traffic such as the data center.

  • Capture traffic during peak utilization times to get a good representation of the different traffic types.

  • Capture traffic on the weekends when most employees are off work.

  • Perform the capture on different network segments.

  • Only capture WAN traffic because traffic to the web is responsible for the largest amount of traffic on a network.

Question

Refer to the exhibit. Host B on subnet Teachers transmits a packet to host D on subnet Students. Which Layer 2 and Layer 3 addresses are contained in the PDUs that are transmitted from host B to the router?

  • Layer 2 destination address = 00-00-0c-94-36-dd Layer 2 source address = 00-00-0c-94-36-bb Layer 3 destination address = 172.16.20.200 Layer 3 source address = 172.16.10.200

  • Layer 2 destination address = 00-00-0c-94-36-ab Layer 2 source address = 00-00-0c-94-36-bb Layer 3 destination address = 172.16.20.200 Layer 3 source address = 172.16.10.200

  • Layer 2 destination address = 00-00-0c-94-36-ab Layer 2 source address = 00-00-0c-94-36-bb Layer 3 destination address = 172.16.20.200 Layer 3 source address = 172.16.100.200

  • Layer 2 destination address = 00-00-0c-94-36-cd Layer 2 source address = 00-00-0c-94-36-bb Layer 3 destination address = 172.16.20.99 Layer 3 source address = 172.16.10.200

  • Skip

4

TestMaker

Score

0 / 10

Correct rate

0%

Correct: 0

Incorrect: 0

Unanswered: 10

 
ankimaker.com

Question list

  • 1

    What are two common causes of signal degradation when using UTP cabling? (Choose two.)

    low-quality cable or connectors, improper termination

  • 2

    Which scenario describes a function provided by the transport layer?

    A student has two web browser windows open in order to access two web sites. The transport layer ensures the correct web page is delivered to the correct browser window.

  • 3

    Which two protocols operate at the top layer of the TCP/IP protocol suite? (Choose two.)

    POP, DNS

  • 4

    An employee of a large corporation remotely logs into the company using the appropriate username and password. The employee is attending an important video conference with a customer concerning a large sale. It is important for the video quality to be excellent during the meeting. The employee is unaware that after a successful login, the connection to the company ISP failed. The secondary connection, however, activated within seconds. The disruption was not noticed by the employee or other employees. What three network characteristics are described in this scenario? (Choose three.)

    quality of service, fault tolerance, security

  • 5

    Refer to the exhibit. If PC1 is sending a packet to PC2 and routing has been configured between the two routers, what will R1 do with the Ethernet frame header attached by PC1?

    remove the Ethernet header and configure a new Layer 2 header before sending it out S0/0/0

  • 6

    Which three layers of the OSI model map to the application layer of the TCP/IP model? (Choose three.)

    application, session, presentation

  • 7

    ok

  • 8

    What does the term “attenuation” mean in data communication?

    loss of signal strength as distance increases

  • 9

    Which two statements describe how to assess traffic flow patterns and network traffic types using a protocol analyzer? (Choose two.)

    Capture traffic during peak utilization times to get a good representation of the different traffic types., Perform the capture on different network segments.

  • 10

    Refer to the exhibit. Host B on subnet Teachers transmits a packet to host D on subnet Students. Which Layer 2 and Layer 3 addresses are contained in the PDUs that are transmitted from host B to the router?

    Layer 2 destination address = 00-00-0c-94-36-ab Layer 2 source address = 00-00-0c-94-36-bb Layer 3 destination address = 172.16.20.200 Layer 3 source address = 172.16.10.200