plumbing code 2
問題一覧
1
Septic tank should be at least _________meters
away from any source of water supply wells
15
2
The National Master Plumbing Association of the
Philippines (NAMPAP) was organized andregistered with the Securities and Exchange
Commission in what year?
1935
3
A registered Master Plumber shall not injure
falsely or maliciously, directly or indirectly, the
reputation of another registered Master Plumber
by reviewing his/her work for the same client
unless the professional services of the former
have been officially ______and all professional
fees have been fully paid by the client.
terminated
4
When shower interceptors are built above
ground, the sub-floor and rough side of walls to a
height of no less than ____mm above the top of
the finished dam or threshold shall be first lined.
With sheet lead or copper or with other durable
and water tight material.
75
5
In water test, the water shall be kept in pipe
system or in portion under test for at least
______minutes before inspection starts. The
system shall be tight at all joints.
15
6
What is AVB in backflow prevention devices?
Atmospheric Vacuum Breaker
7
When potable water is discharge to the drainage
system, it shall be by means of approved air gap
of 2 pipe size diameter from the supply of the
outlet and top surface of the drainage inlet, but in
no case shall be less than ____mm
25 mm
8
Potable water inlet to gravity tank shall be
controlled by a ___ float switch or electrode type
of level water level control to prevent the tank
from overflow.
Float valve
9
What is water fixture supply unit of privately use
bathtub?
2
10
Bell and spigot cast iron soil pipe (CISP) and other
similar joints shall be firmly packed with oakum or
hemp and filled with molten pig lead to n depth
of not less than ____mm.
25.4
11
Solder and fluxes with lead content which
exceeds______ are prohibited in the piping
systems used to conveyed potable water.
0.002
12
What is CS and PS means?
Commercial Standards and Product Standards
13
A stop valve place in service pipe near its
connection with the water main is called:
Corporation stop
14
Plastic pipe shall be supported at every
____interval
1 m
15
Supports of cast iron soil pipe shall be adequate
to maintain alignment and to prevent sagging and
shall be placed within ___meter of the hub or
joint.
0.45
16
A valve or opened by the fall and rise respectively,
of an attached ball floating on the surface
Ball cock
17
Minimum air gaps for water distribution of sinks
and laundry trays when affected by side walls.
57 mm
18
Water inlets to water supported aspirators shall
be equipped with a listed atmospheric vacuum
breaker mounted at least ___ mm above the
aspirator unit.
152
19
Number of water fixture unit for sink or
dishwasher (private use)
2
20
The rim over which water would spill on the floor.
Flood level
21
What is right term for plugging an opening with
oakum, lead or other materials that are pounded
into the annular space?
Caulking
22
It is a valve in which the flood of liquid is cut off
by means of circular disc that fits over and against
the horizontal valve seat. The movement of the
plane of disc is parallel to the normal direction of
flow of water.
Globe valve
23
In plumbing, a secondary pipe line. In sewage, a
common sewer to which no other branch sewer isconnected. It receives sewage from building
sewer service connection only.
Lateral
24
Refers to the public water system laid
underground along the street where house
service is connected
Water main
25
A pipe between the water meter to the fixtures
Distribution pipe
26
A pipe, which convey only waste water or liquid
waste free of fecal matters.
Waste pipe
27
The hubless is used in lieu of the pipe when
caulking and jointing of the pipe is quite difficult.
The hubless pipe (cast iron) is easily joined by use
of _______
Neoprene rubber sleeves
28
The minimum width of septic tank
0.9
29
The commercial size of cast iron pipe is______.
1.5 L
30
Copper tubing shall be supported at each storey
or at a maximum interval of ____meters on
center.
3.00
31
A plumbing permit issued under the plumbing
code shall expire and become null and avoid if the
plumbing work so authorized is suspended or
abandoned at any time after having been
commenced for a period of _____days
120
32
Copper tubing shall be supported at
approximately ____meters interval for piping 38
mm diameter and smaller
1.8
33
All shower compartments, regardless of shape
shall have a minimum finished interior area of ___
square meter and shall be capable of
encompassing a 762 mm diameter circle.
0.6
34
The water used test shall be obtained from a
potable source of supply. A ____ Kpa air pressure
may be substituted for the water test.
344.5
35
Water closet and urinal tank shall be listed with a
ballcock. The ballcock shall be installed with a
critical level atleast ____ mm above the full
opening of the overflow pipe.
25
36
No galvanized wrought iron or galvanized steel
pipe shall be used underground and shall be kept
at least ____mm above the ground.
152
37
Thread on plastic pipe shall be factory cut or
molded. Threaded plastic pipe shall be schedule
____min. wall thickness.
80
38
It is a physical separation, which may be a low
inlet into indirect waste receptor from the fixture,
appliances or device indirectly connected.
Air break
39
No building sewer or other drainage piping or part
thereof, constructed of materials other than
approved for use or within the building shall be
installed under or within ____meters for any
building or structure.
0.6
40
Each cleanout in piping 51 mm or less in size shall
be installed so that there is clearance of not less
than ____mm, in front of the cleanout.
305
41
Any two or more similar adjacent fixtures which
discharge into a common horizontal soil or waste
branch.
Battery of fixtures
42
Sanitary engineering law
RA 1364
43
In case, of renewal of plumbing permit, a fee of
equivalent to ____ of the original fee.
1/2
44
A tee with branch tapped to receive a threaded
pipe or fittings
Tapped tee
45
A water closet consisting of a continuous through
containing water.
Latrine
46
An outhouse or structure used for the deposition
of excrement.
privy
47
The code of sanitation of the Philippines with
Implementing Rules and Regulations.
PD 856
48
A pipe joint obtaining by jointing metal parts with
metallic mixtures which melts at a temperature
below 427o
C and above 149o
C.
Soldering
49
A metallic sleeve, calked or join to opening in a
pipe, into which a plug is screwed that can be
removed for cleaning or examining the interior of
the pipe.
ferrule
50
Normally, a _____mm/hr rainfall intensity is used
around in Metro Manila.
100
51
A vertical vent that is continuation of the drain to
which it connects is a ____
continuous vent
52
A piping system designed to control and convey
excess ground water to a suitable location.
Storm water drainage piping
53
A unit which is equivalent to the flow rate of one
(1) cubic foot of water per minute or 7 ½ gpm of
water.
Fixture unit
54
A fixture designed for the washing of hands or
face, sometimes called washbasin.
Lavatory
55
When no public sewer intended to serve any lot
or premises is available in any thoroughfare or
right of way abutting such lot or premises,
drainage piping from the building shall be
connected to:
Private sewage disposal system
56
A condition in the distribution system where it
could damage, or create condition that will
damage components of the distribution system or
create a nuisance is termed as;
Excessive water pressure
57
Air pressure in drainage pipes greater than
atmospheric pressure.
Back pressure
58
No clerical toilet shall be installed in any building
unless first approved by the
Health officer
59
No clevical toilet shall be installed in any building
unless first approved by the
Health officer
60
All water supply, drainage, venting system and all
fixtures and their traps complete with their
connection.
Plumbing system
61
The minimum size of water supply pipe to a
lavatory is:
3/8 dia
62
Request for inspection by the master plumber to
the administrative authority are required to be
made in advance at least before the work to be
tested
24 hrs
63
The vertical distance that waste travels through
open air between waste pipe and the indirect
pipe waste receptor is
Air gap
64
A means of measurement for vertical waste or
soil stack. It is equal to each floor level or storey
in a building but are always least eight feet
intervals
Branch interval
65
A drain connecting the compartments of certain
fixture to its trap is called
Continuous waste
66
A pipe fitting used to reduce the size of an
opening is called a
Bushing
67
The minimum pressure that should be maintained
for fixtures containing flush tank supplies shall
8 psi
68
A piece of metal fitted under another piece of
that metal or wood over which water is expected
to run is called
Gutter
69
When connecting plastic pipe to other types of
piping, the specific transition intended shall be
made with approved:
Fitting and adapter
70
The inspection of a gas piping system prior to
covering or concealing such pipe is called
Rough piping inspection
71
Copper tubing used for water piping under
concrete slab within a building shall be
Installed without joints where possible
72
The static water pressure at the water meter is 80
psi. at the outlet 40 ft above the meter, the static
water pressure would be approximately
60 psi
73
Vent pipes may offset horizontally when the
distance above the extreme overflow level of the
fixture is at least:
6 in
74
The minimum plumbing permit charge for one
“unit” is;
5 pesos
75
A drainage pipe use to carry main or surface
water, cooling water and similar liquid waste is
Storm sewer
76
Cast iron piping is 10 ft length installed
horizontally, shall be supported at intervals of not
more than
10 ft
77
The flow of water which has gradual and regular
variation over time and space is called
Laminar flow
78
The minimum size building supply allowed by the
code for water is
3/4 in
79
The critical level marking or backflow prevention
device or vacuum breaker is a point established
by the
testing laboratory
80
CPVC water pipe maybe used for hot and cold
water distribution systems
Within a building
81
Plugging an opening with oakum, lead or other
materials that are rounded into place.
Caulking
82
It is a box like collection device which is located
on the exterior of the building and receives storm
water on one side?
Gutter
83
Caulked or screwed joints shall be applicable to
_______
Cast iron
84
The vent pipe serving a combination waste and
vent system with a 4” drain pipe shall be at least:
2 in
85
Building sewer shall be tested by completely filing
the sewer with water from the _____
Lowest to the highest point
86
In the water supply piping slip joints may be used
only on the _____
Exposed fixture supply
87
The drainage pipe running from outside a
buildings foundation to the main sewer is called
______
Building sewer
88
The maximum lead content allowed in pipe used
to convey potable water
8%
89
Is it permissible to place building sewer and
drainage piping in the same trench with the water
service pipe
No
90
Upon issuance of plumbing permit, plumbing
installation shall commenced within
1 year
91
An automatic fill device, most commonly found in
toilet tanks
Ball cock
92
A vertical pipe to convey main waste
Soil pipe
93
The drainage system is subdivided into 8 different
components, drainage, the waste, and the vent.
This is referred to as
DWV system
94
That part of plumbing system extending from
point 4 or 5 feet from the inner face of the
foundation wall of building to the junction with
another sewer
House sewer
95
Equipment which includes all valves and controls
used in the plumbing system which are required
to be accessible or readily accessible is called____
Regulating Equipment
96
Rainwater piping located on the exterior of a
building using galvanized sheet metal shall not be
less than______
28ga
97
. A term used which is contrary to sanitary principle
or injurious to health is _____
Insanitary
98
The maximum fixture unit loading allowed on 2-
inch waste stack is;
16
99
What valve is required a head of each water
supplied appliance, each slip joints or non-
metallic connection?
Control gate valve
100
When pipe makes an angle of not more than 45
degrees with the vertical, it is considered as?
Vertical pipe
plumbing code
plumbing code
Justin Guillermo · 100問 · 2年前plumbing code
plumbing code
100問 • 2年前plumbing code 3
plumbing code 3
Justin Guillermo · 56問 · 2年前plumbing code 3
plumbing code 3
56問 • 2年前Spdi 1
Spdi 1
Justin Guillermo · 4回閲覧 · 100問 · 2年前Spdi 1
Spdi 1
4回閲覧 • 100問 • 2年前Spdi 2
Spdi 2
Justin Guillermo · 98問 · 2年前Spdi 2
Spdi 2
98問 • 2年前Practice Problem
Practice Problem
Justin Guillermo · 70問 · 2年前Practice Problem
Practice Problem
70問 • 2年前PP pre
PP pre
Justin Guillermo · 100問 · 2年前PP pre
PP pre
100問 • 2年前PP Pre 2
PP Pre 2
Justin Guillermo · 100問 · 2年前PP Pre 2
PP Pre 2
100問 • 2年前PP pre 3
PP pre 3
Justin Guillermo · 44問 · 2年前PP pre 3
PP pre 3
44問 • 2年前問題一覧
1
Septic tank should be at least _________meters
away from any source of water supply wells
15
2
The National Master Plumbing Association of the
Philippines (NAMPAP) was organized andregistered with the Securities and Exchange
Commission in what year?
1935
3
A registered Master Plumber shall not injure
falsely or maliciously, directly or indirectly, the
reputation of another registered Master Plumber
by reviewing his/her work for the same client
unless the professional services of the former
have been officially ______and all professional
fees have been fully paid by the client.
terminated
4
When shower interceptors are built above
ground, the sub-floor and rough side of walls to a
height of no less than ____mm above the top of
the finished dam or threshold shall be first lined.
With sheet lead or copper or with other durable
and water tight material.
75
5
In water test, the water shall be kept in pipe
system or in portion under test for at least
______minutes before inspection starts. The
system shall be tight at all joints.
15
6
What is AVB in backflow prevention devices?
Atmospheric Vacuum Breaker
7
When potable water is discharge to the drainage
system, it shall be by means of approved air gap
of 2 pipe size diameter from the supply of the
outlet and top surface of the drainage inlet, but in
no case shall be less than ____mm
25 mm
8
Potable water inlet to gravity tank shall be
controlled by a ___ float switch or electrode type
of level water level control to prevent the tank
from overflow.
Float valve
9
What is water fixture supply unit of privately use
bathtub?
2
10
Bell and spigot cast iron soil pipe (CISP) and other
similar joints shall be firmly packed with oakum or
hemp and filled with molten pig lead to n depth
of not less than ____mm.
25.4
11
Solder and fluxes with lead content which
exceeds______ are prohibited in the piping
systems used to conveyed potable water.
0.002
12
What is CS and PS means?
Commercial Standards and Product Standards
13
A stop valve place in service pipe near its
connection with the water main is called:
Corporation stop
14
Plastic pipe shall be supported at every
____interval
1 m
15
Supports of cast iron soil pipe shall be adequate
to maintain alignment and to prevent sagging and
shall be placed within ___meter of the hub or
joint.
0.45
16
A valve or opened by the fall and rise respectively,
of an attached ball floating on the surface
Ball cock
17
Minimum air gaps for water distribution of sinks
and laundry trays when affected by side walls.
57 mm
18
Water inlets to water supported aspirators shall
be equipped with a listed atmospheric vacuum
breaker mounted at least ___ mm above the
aspirator unit.
152
19
Number of water fixture unit for sink or
dishwasher (private use)
2
20
The rim over which water would spill on the floor.
Flood level
21
What is right term for plugging an opening with
oakum, lead or other materials that are pounded
into the annular space?
Caulking
22
It is a valve in which the flood of liquid is cut off
by means of circular disc that fits over and against
the horizontal valve seat. The movement of the
plane of disc is parallel to the normal direction of
flow of water.
Globe valve
23
In plumbing, a secondary pipe line. In sewage, a
common sewer to which no other branch sewer isconnected. It receives sewage from building
sewer service connection only.
Lateral
24
Refers to the public water system laid
underground along the street where house
service is connected
Water main
25
A pipe between the water meter to the fixtures
Distribution pipe
26
A pipe, which convey only waste water or liquid
waste free of fecal matters.
Waste pipe
27
The hubless is used in lieu of the pipe when
caulking and jointing of the pipe is quite difficult.
The hubless pipe (cast iron) is easily joined by use
of _______
Neoprene rubber sleeves
28
The minimum width of septic tank
0.9
29
The commercial size of cast iron pipe is______.
1.5 L
30
Copper tubing shall be supported at each storey
or at a maximum interval of ____meters on
center.
3.00
31
A plumbing permit issued under the plumbing
code shall expire and become null and avoid if the
plumbing work so authorized is suspended or
abandoned at any time after having been
commenced for a period of _____days
120
32
Copper tubing shall be supported at
approximately ____meters interval for piping 38
mm diameter and smaller
1.8
33
All shower compartments, regardless of shape
shall have a minimum finished interior area of ___
square meter and shall be capable of
encompassing a 762 mm diameter circle.
0.6
34
The water used test shall be obtained from a
potable source of supply. A ____ Kpa air pressure
may be substituted for the water test.
344.5
35
Water closet and urinal tank shall be listed with a
ballcock. The ballcock shall be installed with a
critical level atleast ____ mm above the full
opening of the overflow pipe.
25
36
No galvanized wrought iron or galvanized steel
pipe shall be used underground and shall be kept
at least ____mm above the ground.
152
37
Thread on plastic pipe shall be factory cut or
molded. Threaded plastic pipe shall be schedule
____min. wall thickness.
80
38
It is a physical separation, which may be a low
inlet into indirect waste receptor from the fixture,
appliances or device indirectly connected.
Air break
39
No building sewer or other drainage piping or part
thereof, constructed of materials other than
approved for use or within the building shall be
installed under or within ____meters for any
building or structure.
0.6
40
Each cleanout in piping 51 mm or less in size shall
be installed so that there is clearance of not less
than ____mm, in front of the cleanout.
305
41
Any two or more similar adjacent fixtures which
discharge into a common horizontal soil or waste
branch.
Battery of fixtures
42
Sanitary engineering law
RA 1364
43
In case, of renewal of plumbing permit, a fee of
equivalent to ____ of the original fee.
1/2
44
A tee with branch tapped to receive a threaded
pipe or fittings
Tapped tee
45
A water closet consisting of a continuous through
containing water.
Latrine
46
An outhouse or structure used for the deposition
of excrement.
privy
47
The code of sanitation of the Philippines with
Implementing Rules and Regulations.
PD 856
48
A pipe joint obtaining by jointing metal parts with
metallic mixtures which melts at a temperature
below 427o
C and above 149o
C.
Soldering
49
A metallic sleeve, calked or join to opening in a
pipe, into which a plug is screwed that can be
removed for cleaning or examining the interior of
the pipe.
ferrule
50
Normally, a _____mm/hr rainfall intensity is used
around in Metro Manila.
100
51
A vertical vent that is continuation of the drain to
which it connects is a ____
continuous vent
52
A piping system designed to control and convey
excess ground water to a suitable location.
Storm water drainage piping
53
A unit which is equivalent to the flow rate of one
(1) cubic foot of water per minute or 7 ½ gpm of
water.
Fixture unit
54
A fixture designed for the washing of hands or
face, sometimes called washbasin.
Lavatory
55
When no public sewer intended to serve any lot
or premises is available in any thoroughfare or
right of way abutting such lot or premises,
drainage piping from the building shall be
connected to:
Private sewage disposal system
56
A condition in the distribution system where it
could damage, or create condition that will
damage components of the distribution system or
create a nuisance is termed as;
Excessive water pressure
57
Air pressure in drainage pipes greater than
atmospheric pressure.
Back pressure
58
No clerical toilet shall be installed in any building
unless first approved by the
Health officer
59
No clevical toilet shall be installed in any building
unless first approved by the
Health officer
60
All water supply, drainage, venting system and all
fixtures and their traps complete with their
connection.
Plumbing system
61
The minimum size of water supply pipe to a
lavatory is:
3/8 dia
62
Request for inspection by the master plumber to
the administrative authority are required to be
made in advance at least before the work to be
tested
24 hrs
63
The vertical distance that waste travels through
open air between waste pipe and the indirect
pipe waste receptor is
Air gap
64
A means of measurement for vertical waste or
soil stack. It is equal to each floor level or storey
in a building but are always least eight feet
intervals
Branch interval
65
A drain connecting the compartments of certain
fixture to its trap is called
Continuous waste
66
A pipe fitting used to reduce the size of an
opening is called a
Bushing
67
The minimum pressure that should be maintained
for fixtures containing flush tank supplies shall
8 psi
68
A piece of metal fitted under another piece of
that metal or wood over which water is expected
to run is called
Gutter
69
When connecting plastic pipe to other types of
piping, the specific transition intended shall be
made with approved:
Fitting and adapter
70
The inspection of a gas piping system prior to
covering or concealing such pipe is called
Rough piping inspection
71
Copper tubing used for water piping under
concrete slab within a building shall be
Installed without joints where possible
72
The static water pressure at the water meter is 80
psi. at the outlet 40 ft above the meter, the static
water pressure would be approximately
60 psi
73
Vent pipes may offset horizontally when the
distance above the extreme overflow level of the
fixture is at least:
6 in
74
The minimum plumbing permit charge for one
“unit” is;
5 pesos
75
A drainage pipe use to carry main or surface
water, cooling water and similar liquid waste is
Storm sewer
76
Cast iron piping is 10 ft length installed
horizontally, shall be supported at intervals of not
more than
10 ft
77
The flow of water which has gradual and regular
variation over time and space is called
Laminar flow
78
The minimum size building supply allowed by the
code for water is
3/4 in
79
The critical level marking or backflow prevention
device or vacuum breaker is a point established
by the
testing laboratory
80
CPVC water pipe maybe used for hot and cold
water distribution systems
Within a building
81
Plugging an opening with oakum, lead or other
materials that are rounded into place.
Caulking
82
It is a box like collection device which is located
on the exterior of the building and receives storm
water on one side?
Gutter
83
Caulked or screwed joints shall be applicable to
_______
Cast iron
84
The vent pipe serving a combination waste and
vent system with a 4” drain pipe shall be at least:
2 in
85
Building sewer shall be tested by completely filing
the sewer with water from the _____
Lowest to the highest point
86
In the water supply piping slip joints may be used
only on the _____
Exposed fixture supply
87
The drainage pipe running from outside a
buildings foundation to the main sewer is called
______
Building sewer
88
The maximum lead content allowed in pipe used
to convey potable water
8%
89
Is it permissible to place building sewer and
drainage piping in the same trench with the water
service pipe
No
90
Upon issuance of plumbing permit, plumbing
installation shall commenced within
1 year
91
An automatic fill device, most commonly found in
toilet tanks
Ball cock
92
A vertical pipe to convey main waste
Soil pipe
93
The drainage system is subdivided into 8 different
components, drainage, the waste, and the vent.
This is referred to as
DWV system
94
That part of plumbing system extending from
point 4 or 5 feet from the inner face of the
foundation wall of building to the junction with
another sewer
House sewer
95
Equipment which includes all valves and controls
used in the plumbing system which are required
to be accessible or readily accessible is called____
Regulating Equipment
96
Rainwater piping located on the exterior of a
building using galvanized sheet metal shall not be
less than______
28ga
97
. A term used which is contrary to sanitary principle
or injurious to health is _____
Insanitary
98
The maximum fixture unit loading allowed on 2-
inch waste stack is;
16
99
What valve is required a head of each water
supplied appliance, each slip joints or non-
metallic connection?
Control gate valve
100
When pipe makes an angle of not more than 45
degrees with the vertical, it is considered as?
Vertical pipe