問題一覧
1
A vent in a combustion waste and vent system
shall be approximately equal in area to one half.
Cross section area of the draw pipe
2
DWV material means
Drainage, waste and vent
3
Every passageway to an attic water heater shall
have a solid continuous flooring not less than
24 inches wide
4
Every building in which plumbing fixture are
installed shall have connection to a :
Public and private sewer
5
Allowing for friction and other pressure loss the
available water pressure for fixture is
15 psi
6
The movement of water to the surface of a soil
and into the soil below the surface is
Infiltration
7
The size of supply piping outlet for any gas
appliance shall be not less than
The inlet connection of the appliance
8
The quantity of water required to be supplied to
every plumbing fixture shall be represented by:
Fixture units
9
A pit or receptacle at a low point to which the
liquid waste are drain
Sump
10
A fixture vent pipe increased one pie size its
entire length
May exceed the maximum horizontal length limited by code
11
Fee for one unit of plumbing as plumbing permit
is:
P 5.00
12
A storm drain sometimes located under the
basement floor within the walls of the building
Inside storm drain
13
What is the interval distance between clean-out
along lateral line?
15 m
14
Which type of fire line installation has become
obsolete and seldom installed?
Local vent
15
Generally, what is the standard diameter of
standpipe for buildings more than six stories tall?
6 in
16
A pressure regulator should be installed when
pressure exceeds
80 psi
17
What is the copper content in brass fitting?
85%
18
Is a device located at the bottom of the tank for
the purpose of flushing water closet and similar
fixtures
Flush valve
19
The lowest portion of the interior part of any pipe
or conduit that is not vertical
Invert
20
What is the maximum height for the Hose Cabinet
to be installed from the floor line?
4 ft
21
A structure built, erected and framed of
component structure parts designed for the
housing, shelter, enclosure or support of person,
animals or property of any kind.
Building
22
A pipe connected from building gutter to the
downspout
leader
23
A term used to described soil or waste system
where all piping are threaded pipe tubing or other
rigid construction using recessed drainage fitting
to correspond to the types of piping
Durham System
24
Generally, what is the standard diameter of
standpipe for buildings two or three stories in
height?
4 in
25
The pressure available at the fixture or water
outlet, allowance is made for pressure drop due
at friction loss, head, meter and other losses in
the system during maximum demand period
Residual Pressure
26
In a line of piping is a combination of elbows or
bends, which brings one section of the pipe out of
line but into a line parallel with the original
section.
Offset
27
An open, unoccupied space, bounded on two(2)
or more sides by the walls of the building. An
inner court is a court entirely within the exterior
walls of the building. All other courts are outer
courts.
Court
28
A non-watertight lined excavation in the ground
which receives the discharge of a sanitary
drainage system or part thereof, designed to
retain the organic matter and solids discharging
therefrom, but permitting the liquid to seep
through the bottom and sides of the cesspool.
Cesspool
29
An approved plumbing fixture or device of such
materials, shape and capacity to adequately
receive the discharge from indirect waste pipes,
constructed and located to readily cleaned
Receptor
30
The normal force exerted by a homogeneous
liquid or gas per unit of area on the wall of the
container
Pressure
31
An impairment of the quality of the water to a
degree which creates hazard to the public health
and adversely affects the aesthetic and potable
qualities of waters for domestic use.
Pollution
32
Tube made of plastic material and colored black.
The cross-sectional shape is circular and is
denotes by its outside diameter or O.D.
PE or Polyethylene
33
In what year, NAMPAP President Jaime M. Cabase
spearhead the updating of the Revised National
Plumbing Code?
1996
34
Number of lavatories for Assembly
Places(Theather, Auditorium, Convention
Halls,etc) for public use for 350-female
2
35
In 1902, he was the first Chief of Plumbing
Construction and Inspection
John F. Hass
36
Consists of a loaded air inlet valve, an internally
loaded check valve, two properly located test
cocks and two isolation gate valves.
PVB or Pressure Vacuum Breaker Backflow Prevention Assembly
37
Number of urinal for Office for 420 person
4
38
Revised Plumbing Code of 1999 was approved by
President Joseph Estrada
December 21,1999
39
Plumbing Code for the City of Manila
City Ordinance 2411
40
Drainage Fixture Unit of water closet, public
installation
6
41
When President Ramon Magsaysay did signed the
R.A. 1378, otherwise known as the “PLUMBING
LAW OF THE PHILIPPINES”?
June 18, 1955
42
Type of Joints for soft copper water tubing shall
be made with fittings meeting approved
standards. The tubing shall be expanded with a
proper flaring tool.
Flared joints
43
National Plumbing Code prepared by NAMPAP
was Promulgated and approved by Malacanang
January 28,1959
44
Drainage Fixture Unit of sink, bar, private 38 mm
min waste
1
45
Birth of Plumbing practice in the Philippines
17th Century
46
Approval of House Bill No. 962 also known as RA
No. 1378
1954
47
The indirect waste lines carrying refrigeration
waste shall not be smaller than one (1) inlet
serving not more than 2.8 mm3 of refrigeration
space.
32 mm
48
Each grease trap shall have an approved water
seal of not less than _____in depth or the
diameter of its outlet, whichever is greater
51
49
Cleanouts may omitted on short horizontal
drainage pipe installed at a slope of _____ or less
from the vertical line ( or an angle _____bend)
and;
72 degree ; 1/5 bend
50
Sizing of rainwater piping for two adjacent walls-
add _____of the total wall areas to the roof area
35 %
51
Access to each septic tank shall be provided by at
least two(2) manholes _______ in minimum
dimension or by an equivalent removable cover
slab.
508 mm
52
All septic tank covers shall be capable of
supporting on earth load of not less than ______
when the maximum coverage does not exceed
9m.
14.4 kpa
53
Interceptors or clarifiers for sand and similar
heavy solids shall be so designed and located as
to be readily accessible for cleaning and shall
have a water seal of not less than ____ deep.
152 mm
54
Air test, air is forced into the pipe system until
there is a uniform gauge pressure of _____ or
sufficient to balance a column of mercury 254
mm in height.
34.5 kpa
55
No galvanized wrought iron or galvanized steel
pipe shall be used underground and shall be kept
at least ___ above ground.
152 mm
56
Dome-type strainers shall have a minimum total
net inlet area of ________times the area of the
outlet pipe to which it is connected.
One and one-half
plumbing code
plumbing code
Justin Guillermo · 100問 · 2年前plumbing code
plumbing code
100問 • 2年前plumbing code 2
plumbing code 2
Justin Guillermo · 100問 · 2年前plumbing code 2
plumbing code 2
100問 • 2年前Spdi 1
Spdi 1
Justin Guillermo · 100問 · 2年前Spdi 1
Spdi 1
100問 • 2年前Spdi 2
Spdi 2
Justin Guillermo · 98問 · 2年前Spdi 2
Spdi 2
98問 • 2年前Practice Problem
Practice Problem
Justin Guillermo · 70問 · 2年前Practice Problem
Practice Problem
70問 • 2年前PP pre
PP pre
Justin Guillermo · 100問 · 2年前PP pre
PP pre
100問 • 2年前PP Pre 2
PP Pre 2
Justin Guillermo · 100問 · 2年前PP Pre 2
PP Pre 2
100問 • 2年前PP pre 3
PP pre 3
Justin Guillermo · 44問 · 2年前PP pre 3
PP pre 3
44問 • 2年前問題一覧
1
A vent in a combustion waste and vent system
shall be approximately equal in area to one half.
Cross section area of the draw pipe
2
DWV material means
Drainage, waste and vent
3
Every passageway to an attic water heater shall
have a solid continuous flooring not less than
24 inches wide
4
Every building in which plumbing fixture are
installed shall have connection to a :
Public and private sewer
5
Allowing for friction and other pressure loss the
available water pressure for fixture is
15 psi
6
The movement of water to the surface of a soil
and into the soil below the surface is
Infiltration
7
The size of supply piping outlet for any gas
appliance shall be not less than
The inlet connection of the appliance
8
The quantity of water required to be supplied to
every plumbing fixture shall be represented by:
Fixture units
9
A pit or receptacle at a low point to which the
liquid waste are drain
Sump
10
A fixture vent pipe increased one pie size its
entire length
May exceed the maximum horizontal length limited by code
11
Fee for one unit of plumbing as plumbing permit
is:
P 5.00
12
A storm drain sometimes located under the
basement floor within the walls of the building
Inside storm drain
13
What is the interval distance between clean-out
along lateral line?
15 m
14
Which type of fire line installation has become
obsolete and seldom installed?
Local vent
15
Generally, what is the standard diameter of
standpipe for buildings more than six stories tall?
6 in
16
A pressure regulator should be installed when
pressure exceeds
80 psi
17
What is the copper content in brass fitting?
85%
18
Is a device located at the bottom of the tank for
the purpose of flushing water closet and similar
fixtures
Flush valve
19
The lowest portion of the interior part of any pipe
or conduit that is not vertical
Invert
20
What is the maximum height for the Hose Cabinet
to be installed from the floor line?
4 ft
21
A structure built, erected and framed of
component structure parts designed for the
housing, shelter, enclosure or support of person,
animals or property of any kind.
Building
22
A pipe connected from building gutter to the
downspout
leader
23
A term used to described soil or waste system
where all piping are threaded pipe tubing or other
rigid construction using recessed drainage fitting
to correspond to the types of piping
Durham System
24
Generally, what is the standard diameter of
standpipe for buildings two or three stories in
height?
4 in
25
The pressure available at the fixture or water
outlet, allowance is made for pressure drop due
at friction loss, head, meter and other losses in
the system during maximum demand period
Residual Pressure
26
In a line of piping is a combination of elbows or
bends, which brings one section of the pipe out of
line but into a line parallel with the original
section.
Offset
27
An open, unoccupied space, bounded on two(2)
or more sides by the walls of the building. An
inner court is a court entirely within the exterior
walls of the building. All other courts are outer
courts.
Court
28
A non-watertight lined excavation in the ground
which receives the discharge of a sanitary
drainage system or part thereof, designed to
retain the organic matter and solids discharging
therefrom, but permitting the liquid to seep
through the bottom and sides of the cesspool.
Cesspool
29
An approved plumbing fixture or device of such
materials, shape and capacity to adequately
receive the discharge from indirect waste pipes,
constructed and located to readily cleaned
Receptor
30
The normal force exerted by a homogeneous
liquid or gas per unit of area on the wall of the
container
Pressure
31
An impairment of the quality of the water to a
degree which creates hazard to the public health
and adversely affects the aesthetic and potable
qualities of waters for domestic use.
Pollution
32
Tube made of plastic material and colored black.
The cross-sectional shape is circular and is
denotes by its outside diameter or O.D.
PE or Polyethylene
33
In what year, NAMPAP President Jaime M. Cabase
spearhead the updating of the Revised National
Plumbing Code?
1996
34
Number of lavatories for Assembly
Places(Theather, Auditorium, Convention
Halls,etc) for public use for 350-female
2
35
In 1902, he was the first Chief of Plumbing
Construction and Inspection
John F. Hass
36
Consists of a loaded air inlet valve, an internally
loaded check valve, two properly located test
cocks and two isolation gate valves.
PVB or Pressure Vacuum Breaker Backflow Prevention Assembly
37
Number of urinal for Office for 420 person
4
38
Revised Plumbing Code of 1999 was approved by
President Joseph Estrada
December 21,1999
39
Plumbing Code for the City of Manila
City Ordinance 2411
40
Drainage Fixture Unit of water closet, public
installation
6
41
When President Ramon Magsaysay did signed the
R.A. 1378, otherwise known as the “PLUMBING
LAW OF THE PHILIPPINES”?
June 18, 1955
42
Type of Joints for soft copper water tubing shall
be made with fittings meeting approved
standards. The tubing shall be expanded with a
proper flaring tool.
Flared joints
43
National Plumbing Code prepared by NAMPAP
was Promulgated and approved by Malacanang
January 28,1959
44
Drainage Fixture Unit of sink, bar, private 38 mm
min waste
1
45
Birth of Plumbing practice in the Philippines
17th Century
46
Approval of House Bill No. 962 also known as RA
No. 1378
1954
47
The indirect waste lines carrying refrigeration
waste shall not be smaller than one (1) inlet
serving not more than 2.8 mm3 of refrigeration
space.
32 mm
48
Each grease trap shall have an approved water
seal of not less than _____in depth or the
diameter of its outlet, whichever is greater
51
49
Cleanouts may omitted on short horizontal
drainage pipe installed at a slope of _____ or less
from the vertical line ( or an angle _____bend)
and;
72 degree ; 1/5 bend
50
Sizing of rainwater piping for two adjacent walls-
add _____of the total wall areas to the roof area
35 %
51
Access to each septic tank shall be provided by at
least two(2) manholes _______ in minimum
dimension or by an equivalent removable cover
slab.
508 mm
52
All septic tank covers shall be capable of
supporting on earth load of not less than ______
when the maximum coverage does not exceed
9m.
14.4 kpa
53
Interceptors or clarifiers for sand and similar
heavy solids shall be so designed and located as
to be readily accessible for cleaning and shall
have a water seal of not less than ____ deep.
152 mm
54
Air test, air is forced into the pipe system until
there is a uniform gauge pressure of _____ or
sufficient to balance a column of mercury 254
mm in height.
34.5 kpa
55
No galvanized wrought iron or galvanized steel
pipe shall be used underground and shall be kept
at least ___ above ground.
152 mm
56
Dome-type strainers shall have a minimum total
net inlet area of ________times the area of the
outlet pipe to which it is connected.
One and one-half