問題一覧
1
A water heater is classified as?
Plumbing Appliance
2
Elastomeric gasketed and rubber-ring joints shall comply with ___________ installation standard
IAPMO
3
Depth of the molten pig lead in a caulked joint
25.4 mm
4
Copper tubing shall be fully externally protected with a/an _______________ and fiberglass wrapping installed inside a split rigid casing whenever installed underground.
bitumastic coating
5
Wiped lead joints shall have an exposed surface on each side of a joint not less than _________.
19 mm
6
Copper tube for water supply piping shall have a weight of not less than ________.
Type L
7
Who is the current chairman of the Board of Examiners for Master Plumber?
Reynald B. Ilagan
8
A plumbing permit shall become null and void if the plumbing work has been suspended or abandoned for a period of ___________.
120 days
9
Code on Sanitation of the Philippines
PD 856
10
Common maximum service temperature rating of PVC
140 deg. F
11
Every building where ______________ shall have a sewer service connection to a public or private sewer systems.
plumbing fixtures are installed
12
A hose connection with two-gated outlets permitting two connections of the same or smaller coupling diameter to be taken from a single supply line.
Wye
13
Each fixture directly connected to the drainage system shall be equipped with a ___________.
water-sealed trap
14
For caulked-on closet ring, the minimum overall depth shall be:
2”
15
IPS shall be supported at _______ intervals for piping 19 mm diameter and smaller.
3 m
16
Preferred when a piece of pipe needed is shorter than 150 cm long
Double Hub
17
(ANSI) Pipe Color code for Fire Quenching
Red with White Lettering
18
The Plumbing Code has been in existence for almost __________ since its promulgation before it has been amended
40 years
19
The year when NAMPAP was organized and registered with the Securities and Exchange Commission
1935
20
When was the National Plumbing Code promulgated and approved by the Malacañang?
January 28, 1959
21
Tube made of plastic material and colored black. The cross-sectional shape is normally oval and is denoted by its outside diameter or O.D.
Polybutylene
22
Integrated within an air accumulator vessel which is designed to discharge a predetermined quantity of water into fixtures for flushing purposes
Flushometer Tank
23
Distance of bottom of all pipe tranches to the footing of any adjacent building or structure parallel to it
45 degrees
24
The birth of the plumbing profession in the Philippines is traced back to the _______ century.
17th
25
Trap arm size of Laundry Tub
38 mm
26
Date of the Accreditation of NAMPAP
October 2, 1975
27
In a plumbing unit, how many floor drains are included?
3
28
Vertical support of _________ is placed not less than every other storey height.
Screwed Pipe
29
The Administrative Authority must be notified at least ___ working days before such inspection is intended.
3
30
ASTM means?
American Society for Testing and Materials
31
What principle number: No water closet shall be located in a room or compartment which is not properly lighted and ventilated.
Principle No. 16
32
1 fixture unit is equal to?
1 cu. ft. per minute
33
The distance of water closet or bidet center to center
0.75 m
34
Each member of the board, shall at the time of his appointment be at least _____ of age.
30 years
35
An open return bend usually made up of two 90° bends
Return Bend
36
Any change, addition or modification in construction or occupancy
Alteration
37
Minimum weight of a lead for flashing or vent terminals
14.63 kg per sq.m.
38
A registered master plumber must not supplant another Registered Master Plumber after definite steps have already been taken toward his/her being commissioned to perform the contract
Code of Ethics No. 2
39
Color for Type M copper pipe
Red
40
What is not included in a plumbing unit?
Urinal
41
Voids between pipes and sleeves through concrete floors in the ground shall be appropriately sealed with ________.
Bitumen
42
A pipe flange that is not drilled for bolt holes.
Blank Flange
43
What will happen if a drainage piping is placed at slope of 10mm/m due to structural conditions?
Decrease in DFU loading
44
What section of RA 1378 enumerates the qualification for persons applying for examination?
Section 12
45
What is the accreditation number of NAMPAP?
14
46
All plumbing plans, drawings, diagrams, etc. shall be submitted in ___ sets for permit application.
6
47
The top edge of a receptacle from where water overflows.
Flood Level Rim
48
A pipe or conduit for carrying sewage and wastewater.
Sewer
49
This examination subject in Master Plumbing was originally split into two.
Practical Problems
50
An adjustable tubing connection, consisting of a compression nut, a friction ring, and a compression washer, designed to fit a threaded adapter fitting or a standard taper pipe thread.
Slip Joint
MSTE
MSTE
Justin · 100問 · 2年前MSTE
MSTE
100問 • 2年前Justin
MSTE 2
MSTE 2
Justin · 23問 · 2年前MSTE 2
MSTE 2
23問 • 2年前Justin
PSAD
PSAD
Justin · 50問 · 2年前PSAD
PSAD
50問 • 2年前Justin
HGE
HGE
Justin · 47問 · 2年前HGE
HGE
47問 • 2年前Justin
LOOKS FAM (MSTE)
LOOKS FAM (MSTE)
Justin · 61問 · 2年前LOOKS FAM (MSTE)
LOOKS FAM (MSTE)
61問 • 2年前Justin
MPLE
MPLE
Justin · 41問 · 1年前MPLE
MPLE
41問 • 1年前Justin
Weekly Test 2
Weekly Test 2
Justin · 50問 · 1年前Weekly Test 2
Weekly Test 2
50問 • 1年前Justin
Weekly Test 3
Weekly Test 3
Justin · 50問 · 1年前Weekly Test 3
Weekly Test 3
50問 • 1年前Justin
Refresher SPDI 1
Refresher SPDI 1
Justin · 100問 · 1年前Refresher SPDI 1
Refresher SPDI 1
100問 • 1年前Justin
Refresher SPDI 1
Refresher SPDI 1
Justin · 9問 · 1年前Refresher SPDI 1
Refresher SPDI 1
9問 • 1年前Justin
Refresher Plumbing Code
Refresher Plumbing Code
Justin · 28問 · 1年前Refresher Plumbing Code
Refresher Plumbing Code
28問 • 1年前Justin
Definition of Terms 1
Definition of Terms 1
Justin · 90問 · 1年前Definition of Terms 1
Definition of Terms 1
90問 • 1年前Justin
Definition of Terms 2
Definition of Terms 2
Justin · 90問 · 1年前Definition of Terms 2
Definition of Terms 2
90問 • 1年前Justin
Definition of Terms 3
Definition of Terms 3
Justin · 90問 · 1年前Definition of Terms 3
Definition of Terms 3
90問 • 1年前Justin
問題一覧
1
A water heater is classified as?
Plumbing Appliance
2
Elastomeric gasketed and rubber-ring joints shall comply with ___________ installation standard
IAPMO
3
Depth of the molten pig lead in a caulked joint
25.4 mm
4
Copper tubing shall be fully externally protected with a/an _______________ and fiberglass wrapping installed inside a split rigid casing whenever installed underground.
bitumastic coating
5
Wiped lead joints shall have an exposed surface on each side of a joint not less than _________.
19 mm
6
Copper tube for water supply piping shall have a weight of not less than ________.
Type L
7
Who is the current chairman of the Board of Examiners for Master Plumber?
Reynald B. Ilagan
8
A plumbing permit shall become null and void if the plumbing work has been suspended or abandoned for a period of ___________.
120 days
9
Code on Sanitation of the Philippines
PD 856
10
Common maximum service temperature rating of PVC
140 deg. F
11
Every building where ______________ shall have a sewer service connection to a public or private sewer systems.
plumbing fixtures are installed
12
A hose connection with two-gated outlets permitting two connections of the same or smaller coupling diameter to be taken from a single supply line.
Wye
13
Each fixture directly connected to the drainage system shall be equipped with a ___________.
water-sealed trap
14
For caulked-on closet ring, the minimum overall depth shall be:
2”
15
IPS shall be supported at _______ intervals for piping 19 mm diameter and smaller.
3 m
16
Preferred when a piece of pipe needed is shorter than 150 cm long
Double Hub
17
(ANSI) Pipe Color code for Fire Quenching
Red with White Lettering
18
The Plumbing Code has been in existence for almost __________ since its promulgation before it has been amended
40 years
19
The year when NAMPAP was organized and registered with the Securities and Exchange Commission
1935
20
When was the National Plumbing Code promulgated and approved by the Malacañang?
January 28, 1959
21
Tube made of plastic material and colored black. The cross-sectional shape is normally oval and is denoted by its outside diameter or O.D.
Polybutylene
22
Integrated within an air accumulator vessel which is designed to discharge a predetermined quantity of water into fixtures for flushing purposes
Flushometer Tank
23
Distance of bottom of all pipe tranches to the footing of any adjacent building or structure parallel to it
45 degrees
24
The birth of the plumbing profession in the Philippines is traced back to the _______ century.
17th
25
Trap arm size of Laundry Tub
38 mm
26
Date of the Accreditation of NAMPAP
October 2, 1975
27
In a plumbing unit, how many floor drains are included?
3
28
Vertical support of _________ is placed not less than every other storey height.
Screwed Pipe
29
The Administrative Authority must be notified at least ___ working days before such inspection is intended.
3
30
ASTM means?
American Society for Testing and Materials
31
What principle number: No water closet shall be located in a room or compartment which is not properly lighted and ventilated.
Principle No. 16
32
1 fixture unit is equal to?
1 cu. ft. per minute
33
The distance of water closet or bidet center to center
0.75 m
34
Each member of the board, shall at the time of his appointment be at least _____ of age.
30 years
35
An open return bend usually made up of two 90° bends
Return Bend
36
Any change, addition or modification in construction or occupancy
Alteration
37
Minimum weight of a lead for flashing or vent terminals
14.63 kg per sq.m.
38
A registered master plumber must not supplant another Registered Master Plumber after definite steps have already been taken toward his/her being commissioned to perform the contract
Code of Ethics No. 2
39
Color for Type M copper pipe
Red
40
What is not included in a plumbing unit?
Urinal
41
Voids between pipes and sleeves through concrete floors in the ground shall be appropriately sealed with ________.
Bitumen
42
A pipe flange that is not drilled for bolt holes.
Blank Flange
43
What will happen if a drainage piping is placed at slope of 10mm/m due to structural conditions?
Decrease in DFU loading
44
What section of RA 1378 enumerates the qualification for persons applying for examination?
Section 12
45
What is the accreditation number of NAMPAP?
14
46
All plumbing plans, drawings, diagrams, etc. shall be submitted in ___ sets for permit application.
6
47
The top edge of a receptacle from where water overflows.
Flood Level Rim
48
A pipe or conduit for carrying sewage and wastewater.
Sewer
49
This examination subject in Master Plumbing was originally split into two.
Practical Problems
50
An adjustable tubing connection, consisting of a compression nut, a friction ring, and a compression washer, designed to fit a threaded adapter fitting or a standard taper pipe thread.
Slip Joint