sonicScope

31問 • 10ヶ月前

ユーザ名非公開

通報

問題一覧

In the SonicScope configuration selection during Pre-Job, we make our choice based on

Run Duration, ROP

The SonicScope new Labeling Logic Inputs are

DTmud & Mud Weight for MP6/8/9, Bit size

Can SonicScope provide shear in fast formations?

Yes, from MH

Stonely is measured in which of the below mode

We have RT Leaky-P Capability, but so far it is still a RM only product. By looking at the picture, inside the bandwidth, since Leaky-P is a — __ curve, during processing the __ of the two represents the compressional.

dispersive, faster

I am doing a Go-No-Go deck test with MP3-475, without battery, during statusword monitoring, the toolstatus is displaying 145, what should i do?

Nothing, this is expected

Which TA for SonicScope is related with field dump process, and what we should do in case of this issue?

TA19, follow with dump procedure attached in the TA, don’t try to communicate and dump repeatedly without clear instructions from InTouch

BHA Bit-GVR-TeleScope-MP3-Seismic, plan to do some seismic acquisition during POOH. You have prepared the MP3 with battery installed and initialized with all configures (Drill Normal, Drill Slow, POOH with Seismic Acq) and trip-in time. Suddenly client decided to remove Seismic from the BHA but keep other tools for next run and we need to perform POOH Logging with MP8 Logging, what will you do? Select the best option

Contact JDL SIS, request review for new configure, use magnet to cycle MP3, reprogram the tool with new configure, most of time only POOH changes, change AcqStopDelay to -1

Which partition of MP3 memory is not used or has the least usage so far

For RM Processing in Maxwell, we need dumpfile from partition number _

12, 15

Does MP3-675 and StethoScope-675 use the same battery?

No, they have different alighment slot offset, and depassivation box is also not the same

During the run when tool is at downhole, what will be the expected QP TX reading when checking techlog

100-1200 V or 0

The waveform data stored in the largest partition is

Stacked Waveforms

Regarding SonicScope 475, what is the standard filtering bandwidth used for RT STC computation of monopole high data?

10 - 16 kHz

We changed the design of transmitter of MP6/8/9 for better data quality, so in these tools, which transmitter is closer to the receiver?

Quadrupole Tx

In the dispersion plot shown below, which of the following are the correct axis labels?

X - Frequency, Y - Slowness

What partitions are recording while the tool is in stand-by mode?

What is not a major source of drilling noise which could affect LWD sonic data quality?

Electromagnetic energy from ARC or GVR

From the following list select all the people that need to be involved in the prejob planning stage

CEC for client side, sometimes also sales concern, Cell Manager for field side, as process owner, SIS Expert for data quality side, can also be acoustics domain champion, JDL or PSD for operation side, DEC for drilling side, usually DD invited as well

Which of the SonicScope below has a different transmitter physical configuration from the other 3?

MP4

Under a normal compaction trend, what do you expect to happen to velocity with increasing depth?

Increase

Stoneley Wave is measured in which of the below mode?

Monopole Low

From the illustration below, identify what is C?

Formation Shear Slowness

The dient has requested mp3 stoneley measurement. What is the recommended stabilizer size, needed to ensure a quality measurement? (Select the best option) picture is just for your reference of eccentricity calculation.

1/4 in under gauge

What’s E

Stoneley

From the illustration below, identify what is Curve - A?

Quadrupole Mode Curve

In a dipole mode, regarding collar/tool flexural mode, whose tool has a faster response?

LWD

In this SoniScope log, select the most possible projection label from left to right. Scale 40-240 us/ft

Dtc, Dts, Stonley

Which partition of MP3 memory is not used or has the least usage so far

1 am doing a Go-No-Go deck test with MP3-475 (without battery). During the monito Status Words, Tool_Stat should be...*

145

What are the differences between StethoScope and SonicScope 6/8/9 Batteries? *

They both use different loads for depassivation, They both have different Open Circuit Voltages

Entrance

ユーザ名非公開 · 45問 · 1年前

Entrance

45問 • 1年前

ユーザ名非公開

Mechanics + hydrolics

ユーザ名非公開 · 45問 · 1年前

Mechanics + hydrolics

2. Tool Preparation

2. Tool Preparation

3. Execution and confirmation

ユーザ名非公開 · 74問 · 1年前

3. Execution and confirmation

74問 • 1年前

ユーザ名非公開

問題一覧

In the SonicScope configuration selection during Pre-Job, we make our choice based on

Run Duration, ROP

The SonicScope new Labeling Logic Inputs are

DTmud & Mud Weight for MP6/8/9, Bit size

Can SonicScope provide shear in fast formations?

Yes, from MH

Stonely is measured in which of the below mode

dispersive, faster

I am doing a Go-No-Go deck test with MP3-475, without battery, during statusword monitoring, the toolstatus is displaying 145, what should i do?

Nothing, this is expected

Which TA for SonicScope is related with field dump process, and what we should do in case of this issue?

TA19, follow with dump procedure attached in the TA, don’t try to communicate and dump repeatedly without clear instructions from InTouch

Contact JDL SIS, request review for new configure, use magnet to cycle MP3, reprogram the tool with new configure, most of time only POOH changes, change AcqStopDelay to -1

Which partition of MP3 memory is not used or has the least usage so far

For RM Processing in Maxwell, we need dumpfile from partition number _

12, 15

Does MP3-675 and StethoScope-675 use the same battery?

No, they have different alighment slot offset, and depassivation box is also not the same

During the run when tool is at downhole, what will be the expected QP TX reading when checking techlog

100-1200 V or 0

The waveform data stored in the largest partition is

Stacked Waveforms

Regarding SonicScope 475, what is the standard filtering bandwidth used for RT STC computation of monopole high data?

10 - 16 kHz

We changed the design of transmitter of MP6/8/9 for better data quality, so in these tools, which transmitter is closer to the receiver?

Quadrupole Tx

In the dispersion plot shown below, which of the following are the correct axis labels?

X - Frequency, Y - Slowness

What partitions are recording while the tool is in stand-by mode?

What is not a major source of drilling noise which could affect LWD sonic data quality?

Electromagnetic energy from ARC or GVR

From the following list select all the people that need to be involved in the prejob planning stage

Which of the SonicScope below has a different transmitter physical configuration from the other 3?

MP4

Under a normal compaction trend, what do you expect to happen to velocity with increasing depth?

Increase

Stoneley Wave is measured in which of the below mode?

Monopole Low

From the illustration below, identify what is C?

Formation Shear Slowness

1/4 in under gauge

What’s E

Stoneley

From the illustration below, identify what is Curve - A?

Quadrupole Mode Curve

In a dipole mode, regarding collar/tool flexural mode, whose tool has a faster response?

LWD

In this SoniScope log, select the most possible projection label from left to right. Scale 40-240 us/ft

Dtc, Dts, Stonley

Which partition of MP3 memory is not used or has the least usage so far

1 am doing a Go-No-Go deck test with MP3-475 (without battery). During the monito Status Words, Tool_Stat should be...*

145

What are the differences between StethoScope and SonicScope 6/8/9 Batteries? *

They both use different loads for depassivation, They both have different Open Circuit Voltages