A porter governor could be classified as

In kinematic chain, a quaternary joint is equivalent to

What is a condition where one surface is comparatively free of stress?

Which of the following mechanisms represents an inversion of a single slider crank chain?

A circular bar moving in a round hole is an example of

The following is the inversion of slider crank chain mechanism

For a 4 bar linkage in toggle position, the value of mechanical advantage is

It is a failure prediction theory, which states that a part subjected to any combination of loads will fail (by yielding or fracturing) whenever the maximum shear stress exceeds a critical value. How do you call this failure prediction theory?

For a kinematic chain to be considered as mechanism

The center of gravity of the coupler link in a 4 bar mechanism would experience

It is a design approach where no catastrophic loss can occur as a result of a component failure. What is the design approach?

The instantaneous center of rotation of a circular disc rolling on a straight path is

A rectangular bar in a rectangular hole is the following type of pair

What is the other term for the Maximum-Shear-Stress theory, as a failure prediction theory?

The example of lower pair is

Which one of the following pairs is correctly matched?

"For a planar four bar linkage, the sum of the shortest and the longest lengths cannot be greater than the sum of the remaining two link lengths if there is to be a continuous relative rotation between two members." How do you call the preceeding statement?

Stress concentration in a machine component of ductile materials not so harmful as it is in brittle material because

If the controlling force line for a spring controlled governor when produced intersects the y axis at the origin, then governor is said to be

Mobility of a statically indeterminate structure is

An offset provided in radial cam translating follower mechanism serves to

Which of the following sets of acceleration is involved in the motion of the piston inside the cylinder of a uniformly rotating cylinder mechanism?

If shaft made from ductile material is subjected to combined bending and twisting moments. Calculations based on which one of the following failure theories would give the most conservative value?

What is the direction of the coriolis component of acceleration in a slotted lever-crank mechanism?

In a belt drive, the pulley acts as

Fatigue strength of a rod subjected to cyclic axial force is less than that of a rotating beam of the same dimensions subjected to steady lateral force. What is the reason?

In a slider crank mechanism, the maximum acceleration of slider is obtained when the crank is

Which mechanism produces intermittent rotary motion from continuous rotary motion?

In a hartnell governor, if the stiffness of spring is increased, governor will become

Measure mechanical properties of material are same in a particular direction at each point. This property of the material is known as

The design calculations for members subject to fluctuating loads with the same factor of safety yield the most conservative estimates when using

If some links are connected such that motion between them can take place in more than one direction, it is called

A four bar chain has

Kalian papasa Mechanical Engineering Licensure Exam?

It is one of the rigid members/bodies joined together to form a kinematic chain

What is the combination of applied normal and shear stresses that produces maximum principal normal stress or minimum normal stress, with a third principal stress between or equivalent to the extremes?

In elliptical trammels

Which one of the following mechanisms is an inversion of double slider crank chain?

Which one of the following conversions is used by a lawn sprinkler which is a four bar mechanism?

The maximum distortion energy theory of failure is suitable to predict the failure of which one of the following types of materials?

The governor used in gramophone is the following type

What is the other term for the maximum shear stress theory, as a failure prediction theory?

In a single slider four bar linkage when the slider is fixed. It forms a machanism of

Pulley in a belt drive acts as

What is the difference between the maximum and minimum size limits of a part?

Shaft revolving in a bearing is the following type of pair

A cam is a mechanical member used to impart a desired motion to a follower by direct contact. Which one of the under-listed follower motion types will produce the least jerk to the system?

If the size of a standard specimen for fatigue testing machine is increased the endurance limit for the material will

The maximum strain theory which applies only in elastic range of stresses are also known as

Who postulated the maximum distortion energy theory?

The example of rolling pair is