問題一覧
1
These types of paints are used mainly for concrete and masonry surfaces.
Latex Paint
2
Approximately, how many psi is equivalent to 1 MPa?
145.038 psi
3
What is the minimum Plasticity Index for Aggregate Surface Course?
4
4
What is PCCP?
Portland Cement Concrete Pavement
5
What sieve No. is the maximum particle passing for Sand used in Field Density Test?
Sieve No. 10
6
What is the maximum horizontal thickness per layer for embankment subject for compaction?
200mm
7
What is the Class if the stones are weighing from 60kg to 100kg?
Class C
8
What is the standard unit weight per meter of 32mm steel bars?
6.314 kg/m
9
As per specifications, what is the spacing of Reflectorized Thermoplastic Rubble strips?
200 - 500 mm
10
What is the frequency for Status of Test report?
monthly
11
What is the concrete class used for Item 510 - Concrete Slope Protection?
Class B
12
The following are trees that can be used as Timber Guard Rails except one;
Mahogany
13
What is the tensioe strengty of Rubber Water Stops?
17 MPa
14
The following are types of slump, except one;
False Slump
15
What is the CBR Value for Item 200?
30%
16
This is the unit of measure for Item 402 - Timber Structures
Span
17
What is the ph Value of water allowed in concrete mix?
4.5 to 8.5
18
How high above the ground should the chevron signs be installed in urban areas?
2.20 m
19
What is the coefficient of friction of the hardened concrete surface pavement?
0.25
20
Water-Reducing and Accelerating Admixture is what type of admixture?
Type E
21
Compaction of embankment shall continue until a uniform density of not less than ______ of the maximum dry density is obtained.
95%
22
This is the sudden halt of the load indicating pointer and the corresponding stress during testing of reinforcing stewl bars?
Yield Point
23
What is the rate of application for Bituminous Prime Coat?
1-2 l/sqm
24
What is minimum Free-Haul distance?
600m
25
What is the Specific Gravity of Magnesium Sulfate used for soundness test?
1.295 to 1.308
26
Branches of trees extending over roadbed shall be trimmed to give a clear height of ________ above road surface.
6m
27
What is maximum Loss of Ignition of cement?
3%
28
What is the surface irregularity tolerance of base course?
5mm
29
What is the minimum uniform density of crushed slag used for PCCP in kilogram/cubic meter?
1,120
30
What is the amount of Hydrated Lime to be added to the Bituminous mixture?
0.5-1.0%
31
What is the spacing of "shesr keys" that provide inter lock between geofoam blocks?
3.0 - 4.5 m
32
Which of the following Gauge No. Of Galvanized Iron Sheets is the thickest?
No. 18
33
What is the minimum flexural strength of beam sample when tested by Mid-Point Method?
4.5 MPa
34
What do you call the common defect of asphalt pavement which is mainly caused by excess of bituminous binder?
Bleeding
35
Polymer-based chemical soil additive shall be less than ______ by weight of soil.
2%
36
What is the minimum volume per stone to be used for Item 508 - Hand-Laid Rock Embankment in m^3?1
0.015
37
At least, how many days the contractor shall notify the engineer before they intend to start top soil stripping operations?
5 days
38
For Item 603 - Guard Rails, the bolts shall of sufficient length to extend beyond the nuts at least 5 mm but not more than _____?
10 mm
39
What is the maximum water cement ratio for Class A concrete?
0.53
40
What is the ability of asphalt pavement to bend without breaking?
Flexibility
41
What is the weather limitations or the minimum ambient temperature in degrees Celsius for Slurry System for Road Surface Treatment?
10
42
What is the test that determines amount of asphalt or bitumen in the bituminous mixture?
Extraction
43
What is the PI for embankment?
max. of 6
44
These types of paints are used mainly for wood.
Enamel Paint
45
What is the concrete class used for Item 515 - Mechanically - Stabilizer Earth (MSE) Retaining Walls?
Class A
46
For Thickness determination using core asphalt, how many measurements should be taken on its quarter points on the periphery?
4
47
What is the most fluid grade of medium curing cutback asphalt?
MC-30
48
What is the minimum thickness of bedding material beneath the pipe?
100mm
49
What is minimum sampling requirement foe Mineral Filler?
2.5 kg
50
What is minimum weight of Gravity Hammers used in pile driving?
2,000 kg
51
What is the unit of measure for Item 307 - Bituminous Plant-Mix Surface Course-General?
square meter
52
The entire hydroseeded area shall be grown-in and maintained for how many Calendar Days from the date of the hydroseeding completion?
60-90
53
As per specification, what is the maximum decantation value?
3%
54
The optimum asphalt content is the average of the 3 asphalt contents at Maximum Stabilit, Maximum Unit Weight and ________.
4% Air Voids
55
For Item 204, what is the amount of cement to be added to the soil aggregate by mass percent of the dry soil?
6-10%
56
What is the surface irregularity tolerance of subbase course?
20mm
57
For Pipe Culvert, width of excavation shall be at least _______ greater than the horizontal diameter of the pipe?
300mm
58
How high above the ground should the chevron signs be installed in rural areas?
1.50 m
59
What is the radius of the edges of sidewalk and transverse cuts?
15mm
60
What is the maximum tolerance on the mass of one piece of steel bar?
+ - 6.0%
61
What is the ISO Compliance for Portland Cement?
ISO:9001
62
What is the minimum pull - offs per system or span of Carbon Fiber Sheets?
2
63
All materials below subgrade level to a depth ______ shall be excavated.
150mm
64
What is the least fluid grade of rapid curing cutback asphalt?
RC-70
65
Concrete not in place within _______ shall not be used/discarded.
1.5 hours
66
What is the maximum abrasion loss for Lime Stabilized Road Mix Base Course?
50%
67
What is the rate of application of Airtol geobinder in terms of kg/hectare?
1,500
68
What is the maximum PI value for Item 202 Crushed Aggregate Base Course?
6
69
What is sieve no. that seperates between coarse and fine aggregates of Item 300, Aggregate Surface Course?
No. 10
70
What is the dimension tolerance for Gabions?
+-5.0%
71
What is the least fluid grade of slow curing cutback asphalt?
SC-3000
72
What sieve no. Is equivalent to 1.70mm sieve opening?
Sieve No. 12
73
What is the minimum number of rivets and bolts for testing purposes for Item 403, Metal Structures?
5
74
The following are the most commonly packed in paper bags of Item 701 - Construction Lime ( Hydrated), except;
12.5 kg
75
Which of the following Schedule No. of Galvanized Iron Pipes is the thinnest?
No. 5
76
What is the frequency for Certificate of Quality Control Assurance (CQCA) report?
weekly
77
This is the rate of dilusion for each layer for Item 206.
1:5 to 1:9
78
Which of the following Gauge No. of Galvanized Iron Sheets is the thinnest?
No. 22
79
For Pre-cast curb and guttet, the width at the top shall not be more than?
20 cm
80
What is the unit of measure for Item 206?
liter
81
What is the rate of application for Bituminous Tack Coat?
0.2-0.7 l/sqm
82
What is minimum thickness of aluminum sheeting used for warning, regulatory and informatory signs?
3 mm
83
What is the minimum distance between reinforcing steel bars?
40mm
84
For earth berms, what is the minimum acceptable Maximum Dry Density (MDD)?
90%
85
What is the weight of the hammer used for AASHTO T-180 (Modified Proctor Test)?
10.0 lbs
86
What is the slump of workable concrete when not vibrated?
40-75mm
87
What is Item 509?
Sheet Piles
88
How many spheres are used in Abrasion Test, Grading C at 500 revolutions?
8
89
The following are the benefits of compaction, except one;
Increase Permeability
90
What is the device that measures the relative hardness of asphalt?
Penetrometer
91
What is the specific gravity of Portland cement?
3.15
92
The maximum size aggregate for structural concrete shall be less than ______ spacing of the bars.
2/3
93
Dial and Armored Stem Thermometer should be inserted in the mixture to a minimum depth of _______?
6"
94
What is th soaking time of the sample tested for California Bearing Ratio (CBR) Test?
96 hours
95
What is the maximum rate of application of Curing Compound used for PCCP?
0.30 L/sqm
96
What is the minimum average compressive strength of load bearing concrete hollow block (CHB)?
1,000 psi
97
This Item consist of right-of-way monuments, kilometer posts, and marker and guide post.
Item 602
98
Which of the following Schedule No. of Galvanized Iron Pipes is the thickest?
No. 160
99
What is minimum penetration of all piles for Bridge Construction?
6m
100
What is the minimum dry compressive strength of bituminous mixture?
1.4 MPa