問題一覧
1
What is the spec used for installation of hex drive bolts?
BAC5004-2
2
When damage is detected via tactile inspection methods, what is the depth detected?
greater than .001” depth
3
Which seal type requires a continuous and adequate squeeze out?
Fay seal
4
Which specification is used to determine surface and edge requirements for aluminum structures?
BAC5300-1
5
Which seal application has the following requirements; should be free of voids, re-entry’s, bubbles, and should be smooth?
fillets seal
6
How much excess sealant is allowed after day seal is squeezed out?
none
7
Where is a bolt part number typically found?
head
8
Which two features need to be checked when inspecting the head of a flush head lock bolt?
gaps, flushness
9
What features must be checked on universal head rivets?
damage, gaps
10
What is the correct feeler gage to use on a flush head 3/16” solid aluminum rivet?
.003”
11
When collars are installed on hex drive bolts, how much finish removal is allowed? (Pick 2)
no finish removal allowed & only where frangible collar break off
12
Which specification is used for bolt installations?
BAC5009
13
What is the max number of washers allowed on the pin side of a hex drive bolt?
2
14
Which features must be checked on the tail of an aluminum rivet installation?
minimum height and width
15
Which specification controls fuel cell sealant applications
BAC5504
16
Which specification is used for CIC applications?
BAC5877
17
Which specification is used for installation of locking devices?
BAC5018
18
Which feature is not checked on a bolt installation?
pin color
19
Which specification is used for application of BMS 10-11 primer?
BAC5736
20
What is the acceptable amount of threads protruding from a hex drive bolt collar?
None
21
Which specification controls clad skin surface finish requirements?
BAC5615
22
Which specification is commonly used to determine torque requirements of screws?
BAC5009
23
What is the most important consideration when performing a shakedown inspection?
safety
24
What is the correct feeler gage to use on the head side of a 1/4” protruding head lock bolt?
.006”
25
What is a common name for a lock bolt?
Huck Bolt
26
What is a common part number for a modified universal head rivet?
BACR15FT6
27
What is a common part number for a hex drive bolt?
BACB30VT6
28
Which specification is used for lock bolt installations?
BAC5004-2
29
When collars are installed on lock bolts, how much finish removal is alllowed? (Pick 2)
axial burnishing & finish removal allowed in fuel cell
30
What is the correct feeler gage to use on a 1/4” protruding head hex drive bolt?
.006”
31
What is the correct feeler gage to use on a universal head 3/16” solid aluminum rivet?
.003”
32
What is the maximum allowable protrusion for a shim or a filler?
.100”
33
Which two features need to be checked when inspecting the head of a flush head hex drive bolt?
gaps, flushness
34
What is the correct feeler gage to use on the head side of a 1/4” hex head bolt?
.005”
35
What is a common structural member common to the interior of an airplane?
stringer
36
Which two gages are used to check pin length on a bolt installation?
pin protrusion gage and caliper
37
When should FOD be considered a defect?
any inspection
38
What is the max blend depth that can be done without a rejection tag?
none of the above
39
Which specification controls fat seal and fillet seal in non-fuel cell areas?
BAC5000
40
Which cleaning process is appropriate for day seal preparation?
wet wipe then dry wipe
41
What is the spec used for installation of a solid aluminum rivet?
BAC5004-1
42
Which specification is used for installation of shims and fillers?
BAC5430
43
What does 13d relate to on a rivet installation?
minimum tail width
44
What is the correct feeler gage to use on the nut side of a 1/4” flush head bolt?
.006”
45
For integral fuel cell sealing, when is brushcoat required?
before fillet seal
46
What tool is used to check pin length on a lightweight hex drive bolt?
Red HiLite Gages
47
Which defect is not commonly found on a seal application?
dents
48
What is the correct feeler gages to use in the collar side of a 1/4” flush head lock bolt?
.003”
49
What color is the pin on a lightweight hex drive bolt?
orange
50
What is the correct feeler gage to use on a 3/16” flush head hex drive bolt?
.003”