What system of demonstrable partitions is designed to best allow erection of only one side of the partition so other trades can work?

The spacing for carrying channel on a suspended ceiling:

What does O.C. mean?

What would be least likely to happen, if gypsum board is stocked vertically?

What technique would you use, when applying gypsum board to a curved wall?

When applying drywall to a suspended ceiling system, screw fasteners are spaced a maximum of ___ inches o.c. in the field of the board, and ___ o.c. along abutting ends and edges of the board.

The limiting height in solid partitions is:

A scaffolding must be ___ high before you need a safety rail

Cracking on gypsum would most likely occur because of the:

Which type of studless partition would weigh the least

Which type of studless partiton provides the highest fire rating?

The tool which is used for texturing over drywall is:

What could be the cause, if texturing is not sticking to the ceiling?

The best method of installing drywall parallel to the studs is:

What are Z-bar applications used for?

____________ will increase soundproofing:

What system would give the greatest fire protection to a column?

Use _______ for the best method of fire protection.

A sealer _____ to a wall

Damaging vinyl covering in a wall is caused by

Drywall should be nailed off at

What would cause dark lines in the paper, after a ceiling has been textured?

Veneer paneling is found in the

The term "hide" pertains to:

What is the recommended method of attachment to metal studs (2 layers)?

Of the following, which system of demountable partitions could be erected in the shortest possible time?

Which type of gypsum wallboard can you apply-water-bsde texture?

A water-level hose is filled by:

Steel studs are treated because:

The correct stud to use for one layer of vinyl finish board is ___, so the electrician can install conduit.

Use ______ when welding exterior studs.

_________ welded is found where workers are making up a scaffold with tubular pipe:

The advantage of installing two layers of Type X drywall is:

How do you prevent cracking at corners, when installing drywall?

How far apart should steel studs be placed, when are used as hangers in a suspended ceiling?

The best means of securing rigid plastic foam, plus 5/8-inch face-ply to a concrete wall is:

If a drywall mechanic sprayed a ceiling before the joint has dried, the results would be:

A drywall mechanic installed 5/8-inch drywall in a ceiling using Type W screws spaced 12 inches on center on the edges, ends, and in the field, with screw heads slightly below the surface.

The most important factor is _____, when installing a heavy metal door.

If a drywall mechanic is crimping corner bead, you would expect that:

Which is NOT correct, when applying tongue-and-groove gypsum sheathing?

When installing a rail-high partition:

_____ is used to fasten face sheet to drywall

What should boards supporting drywall stacks be

When installing pre-decorated gypsum board, and you find there are differences in color, pattern or finish, where should you place the different sheets?

You are told to first cut a sheet of gypsum board to size for a curved wall and then to score the back of the sheet at 1-inch intervals.

_______ is NOT true, about applying water-resistant panels in a bathroom:

What would you use to repair a cracked or damaged texture coat

What should you do when you paint over a texture coat

The best drywall to which to apply water-base texture is:

When surfacing walls in a repair project, _______ NOT correct:

You should ________, when storing drywall to be used on a job.

You are working on a 6 ft. X 2 1/2 ft., 5 ft. High., metal rolling scaffold. It's rollers rest on a surface that is 2 degrees from level. When it comes time to move the scaffold to a different area, you instruct a worker to move the scaffold while you are still on it. You have proceeded:

What is not correct about steel studs used for partitions?

Where are rips used?

______ is when the edge of gypsum board runs vertically with the studs:

Gypsum board may be mounted with adhesive to a concrete wall with cut nails. When this is done, the nails are placed:

Gypsum board is not always the same texture and porosity. To compensate for this you should:

The least affected by the humidity factor at a project is:

What kind of furring strips should be used in an masonry block wall?

A "dimple" is

For heavy metal doors double metal studs should be installed:

Nails are spaced ______, in double nailing

The reason may be ______, if a texture spray fails to stick to the ceiling.

If 12 feet long gypsum boards are stored on risers, they should be at least 4 inches wide and placed directly under each other vertically within ____ inches of board ends and no greater than ____ inches apart

What is NOT the right thing to do, if you are going to nail 3/8-inch drywall over existing drywall?

A double brush is used for texturing because:

What causes a texture mix to be "lumpy?"

How do you match up new partition walls with existing partitions on a remodeling job?

What type of stud would you use if a customer wanted a partition wall set up in a hurry?

Where would you find wood-grain gypsum panels?

How many coats of joint compound and layers of tape do you need for a factory edge?

The best interlocking partition is:

The surface around screws that bulge onab dry wall is caused by

What is the best method of repairing tape that has blistered?

For an exterior soffit you would use:

The normal height for office partitions is

To seal water board you would:

What is the fire rating on a 2 inch x 4 inch wall with 5/8 Type X on each side

______ is NOT needed in a heavy metal door and frame.

If money is no object, what would you use in a business office to achieve wood finished on walls?

How would you attach gypsum board to a block wall?

When attaching ceramic tile, you do not need to tape the walls.

Which one of the following statements about drywall mud is NOT correct?

The best choice of hardware for a 5/8 inch drywall application to affix layer of drywall over a foam-insulated wall:

When applying texture to a wall where the roughness of the surface is inconsistent, how would you first prepare the wall?

What is the disadvantage of putting two light boxes on the same stud when installing moveable partitions?

If the general application for screw fasteners on a suspended ceiling is 12 inches o.c., what application would be necessary for the ceiling to be fire-rated?

What is "spaling"?