ATE MULTIPLE Choice

79問 • 1年前

問題一覧

Which of the following does not apply? To be elegible for a mechanic certificate and associated ratings, a person must —

or in the case of an applicant who does not meet requirements and who is employed by a foreign air carrier, have his certificate endorsed “Valid only outside the United States

The FAA stands for

Federal Aviation Administration

Advisory Circulars (AC)

provide guidance for complying with a related FAR

Airworthiness Directive # 2003-18-10 was issued

in September 2003

ATA stands for

Air Transport Assoication of America

Information distributed to the maintenance technicians in the form of an Airworthiness Alerts is gathered from

Malfucntion or Defect Reports

STC stands for

Supplemental Type Certificate

Service Bulletins (SB)

are sometimes mandatory

FAR Part 21 covers

Certification procedures for products and parts

FAR Part 65 covers

airmen other than flight crew members

A “TSO” stamp on a part means

that the part is approved for installation on certified aircraft

Which of the following is not a category of AD’s?

Non-Regulatory information

Service bulletins are not issued to notify others of:

proposed changes to the TCDS

FAR Part 91.417 requires that the aircraft maintenance records contain the current status of applicable AD’s the excluding:

Notification procedures for compliance

Compliance requirements are established for safety reasons and may be stated in many different ways, one way that it is not used would be:

number of years from manufacture

Who is responsible for the compliance with AD’s?

registered owner or operator

Which is correct about an AD numbered 1996-12-10 R?

Revised-R

When do emergency AD’s become effective?

upon the owners receipt

Which is not a category in that AD’s are published?

Malfucntion or Defect Report

Which of the following items does not represent an AD applicability?

food services on-board Trans-Atlantic flights

Given the following two statements: X. Malfunction or Defect Reports give the general-aviation community information to identify service difficulties and safety problems found during maintenance X. Advisory Circulars inform the aviation community, in a systematic way, about regulatory information of interest

X is true, Z is false

The approval for the manufacture of a component for use in certified aircraft is covered in which FAR?

Part 21

How may emergency AD’s be distributed?

Fax

Consider the following two statements: X. NPRM provides a comment period where you may provide your own input by submitting data, views or arguments for or against Z. A major change can be submitted to the FAA to a previously approved design type as long as the change doesn’t require a new certificate

X is true, Z is true

Airworthiness standards for helicopter rotor blades would be located in which FAR?

Part 27

According to FAR Part 43, changing the landing gear wheels of a Cessna 150 to floats would be considered?

an alteration to the aircraft

True or False FAA AC 43.13-1B can be used as approved data to repair an aircraft that has a defect not levered within the manufacturers maintenance manuals

False

True or False A discrepancy between orb different rudder rigging travel limits between an aircraft’s TCDS and the aircraft’s manufacturer’s maintenance manual, follow the manufacturer’s maintenance instructions.

false

True or False A manufacturer’s service letter may be used as a justification to facilitate a repair different from one mandated by an AD as long as it accomplished an acceptable level of safety as the requirements of the AD.

true

Where can you find aircraft data and specifications for certificated aircraft when there are only 20 registered?

Aircraft listing

Are you required to notify the FAA when an AD has been accomplished?

Maybe

Of the following two statements: A. FAA Advsiory Circulars are never binding B. A high premature failure rate amongst an aircraft’s pitot maybe brought to your attention though an air worthiness alert

A is false, B is true

The main point of contact between the FAA and an individual technician is the

FAA regional office

Helicopter rotor blades are certificated under 14CFR Part

A standardized organization or maintenance information is found in

ATA iSpec 2200

A part manufactured for installation on an FAA certified aircraft by a person other than the aircraft manufacturer maybe approved by the provisions of a/an

Parts Manufacturer Approval

Cheating on an FAA exam may be tolerated if certain requirements are met and the FAA administrator is familiar with your limitations

false

What is the minimum passing grade of all FAA exams?

70%

Falsely reproducing aircraft records can result in ___

certificate suspension or revocation

The FAA requires a fixed base of operation for an inspection Authorization to be approved

true

A mechanic must hold their license for __ years to be eligible for an Inspection Authorization

The applicant form, to become a certified mechanic, is Form ___

8610-2

____ months of practical experience, working on aircraft, are required to apply for the airframe and powerplant certificate l, if the applicant has not attended a certified school

Maintenance managers, that request shortcuts to be made in repair or maintenance, will always stand by their requests under oath in court

false

An airframe and powerplant mechanic may perform, and return to service, a 100 hour inspection on an aircraft, propellor, and engine.

false

A powerplant mechanic may perform a major repair to an aircraft engine but a ___ is required to return it to service

Inspection Authorization (IA)

The recent experience requirements of the mechanics certificate may be fulfilled through supervising maintenance or alteration of aircraft.

true

Repairing an altimeter is a privilege of the airframe mechanic

false

Propeller knowledge and testing would be included in what rating?

powerplant

The mechanic ratings include the ____ and ____

airframe, powerplant

A certified mechanic must be at least __ years of age

Refusing to submit to drug and alcohol testing is ____

grounds for revoking their certificate

The FAA must be notified within ___ days of a change of address of any person holding a mechanic certificate

A mistake in recording the part number, is a part installed on an aircraft, if unintentional, is cause for revoking a mechanics certificate

false

The two methods by which an applicant for a mechanics certificate may retake a failed written test include _____ and _____

waiting 30 days, receive additional instruction with a signed statement

The mechanic certificate must be renewed each year or it will expire

false

If you ____ your mechanic certificate, this means you return it voluntarily

surrender

A conviction, for the sale of marijuana, may result in your mechanic certificate being suspended or revoked

true

The primary difference between the mechanic certificate and the repairman certificate is that the mechanic can perform more difficult repairs than the repairman.

false

The mechanic, and the repairman certificates are considered to be different classifications by the FAA

true

14 CFR Part 65 relates to the verification of airmen other than ___ crew members

flight

Simple or minor preservation operations and the replacement of small standard parts not involving complex assembly operations best describes:

preventative maintenance

An aircraft overflew its 100 hour inspection by two hours reaching your inspection facility. You complete your inspection and return it to service. You record the next 100 hour inspection as being sure in __ hours

To apply for a mechanic certificate and rating, an applicant may provide documentary evidence that attests to ___ months of practical experience equally performing the duties of both airframe and powerplant duties.

An airframe certificated mechanic may perform the entire 100 hour inspection upon an aircraft and return it to service

false

Aircraft that operated under a progressive inspection program are required to undergo an annual inspection every year

false

A conviction for the violation of any Federal or state statue relating to the growing, processing, manufacturing, sale, disposition, possession, transportation, or importation of narcotic drugs, marijuana, or depressant or stimulant drugs or substances is grounds for- 1) Denial of an application for any cerficate or rating issued under this part for a period of up to 2 years after the date of final conviction; or 2) suspension or revocation of any certificate or rating issued under this part

If the holder of an inspection authorization changes his fixed base of operation,

he many not exercise the privileges of authorization until he has notified the FAA Flight Standards District Office or International Field Office for the area in which the new base is located, in writing, of the change

To be elegible for a repairman cerficate (experimental aircraft builder) an individual must - Which of the following is not true

Be at least 16 years of age

Refusal by the holder of a cerficate issued under this part to take a drug test required under the provisions of appendix I to part 121 or an alcohol test required under the provisions of appendix J to part 121 is grounds for- Which of the following is true 1) Denial of an application for any certificate or rating issued under this part for a period of up to 1 year after the date of such refusal and; 2) suspension or revocation of any certificate of any certificate or rating issued under this part

1&2

Which of the following does not apply To be elegible for an inspection authorization, an applicant must-

pass a written test, oral test, and practical exam covering the construction and maintenance of aircraft

Each inspection authorization expires:

march 31st of each odd numbered year

A mechanic with only an airframe rating may obtain an inspection authorization valid only for the maintenance, inspection, repair, and alteration of the aircraft frame

false

The holder of an inspection authorization may supervise a progressive inspection

true

When a mechanic exercises the privileges of an inspection authorization he shall keep it available for inspection for which of the following:

all of the above

A certificated A&P mechanic may approve and return to service an airframe, powerplant, or propellor or any related part or appliance

after he has performed, supervised, or inspected a major repair or alteration for an aircraft in the light sport category

A certified mechanic may not exercise the privileges of his certificate and rating unless, within the preceding 12 months- A) the administrator has found that he is able to do that work B) he has for at least 6 months: - served as a mechanic under his certificate and rating -technically supervised other mechanics - supervised, in an executive capacity, the maintenance or alteration of aircraft

true

An A&P rated mechanic may do which of the following

supervise the maintenance, preventative maintenance or alteration of an aircraft or appliance

Which of the following does not apply

documentary evidence, satisfactory to the administrator, of at least 15 months of practical experience with the procedures, practices, materials, tools, and equipment generally used in constructing, maintaining, or altering airframes, or powerplants appropriate to the rating sought

ATE 103 - Q1

ATE 103 - Q1

ATE MULTIPLE Choice

ATE MULTIPLE Choice

final

final

Heat Treatment Test

Heat Treatment Test

ate 109 materials and processes

Miles T. · 90問 · 1年前

ate 109 materials and processes

ATE 101 FINALE

ATE 101 FINALE

worksheet one

worksheet one

Test 3reezy

Miles T. · 61問 · 11ヶ月前

Test 3reezy

61問 • 11ヶ月前

Miles T.

Sheet Metal Final

Miles T. · 157問 · 11ヶ月前

Sheet Metal Final

157問 • 11ヶ月前

Miles T.

問題一覧

Which of the following does not apply? To be elegible for a mechanic certificate and associated ratings, a person must —

or in the case of an applicant who does not meet requirements and who is employed by a foreign air carrier, have his certificate endorsed “Valid only outside the United States

The FAA stands for

Federal Aviation Administration

Advisory Circulars (AC)

provide guidance for complying with a related FAR

Airworthiness Directive # 2003-18-10 was issued

in September 2003

ATA stands for

Air Transport Assoication of America

Information distributed to the maintenance technicians in the form of an Airworthiness Alerts is gathered from

Malfucntion or Defect Reports

STC stands for

Supplemental Type Certificate

Service Bulletins (SB)

are sometimes mandatory

FAR Part 21 covers

Certification procedures for products and parts

FAR Part 65 covers

airmen other than flight crew members

A “TSO” stamp on a part means

that the part is approved for installation on certified aircraft

Which of the following is not a category of AD’s?

Non-Regulatory information

Service bulletins are not issued to notify others of:

proposed changes to the TCDS

FAR Part 91.417 requires that the aircraft maintenance records contain the current status of applicable AD’s the excluding:

Notification procedures for compliance

Compliance requirements are established for safety reasons and may be stated in many different ways, one way that it is not used would be:

number of years from manufacture

Who is responsible for the compliance with AD’s?

registered owner or operator

Which is correct about an AD numbered 1996-12-10 R?

Revised-R

When do emergency AD’s become effective?

upon the owners receipt

Which is not a category in that AD’s are published?

Malfucntion or Defect Report

Which of the following items does not represent an AD applicability?

food services on-board Trans-Atlantic flights

X is true, Z is false

The approval for the manufacture of a component for use in certified aircraft is covered in which FAR?

Part 21

How may emergency AD’s be distributed?

Fax

X is true, Z is true

Airworthiness standards for helicopter rotor blades would be located in which FAR?

Part 27

According to FAR Part 43, changing the landing gear wheels of a Cessna 150 to floats would be considered?

an alteration to the aircraft

True or False FAA AC 43.13-1B can be used as approved data to repair an aircraft that has a defect not levered within the manufacturers maintenance manuals

False

false

true

Where can you find aircraft data and specifications for certificated aircraft when there are only 20 registered?

Aircraft listing

Are you required to notify the FAA when an AD has been accomplished?

Maybe

A is false, B is true

The main point of contact between the FAA and an individual technician is the

FAA regional office

Helicopter rotor blades are certificated under 14CFR Part

A standardized organization or maintenance information is found in

ATA iSpec 2200

A part manufactured for installation on an FAA certified aircraft by a person other than the aircraft manufacturer maybe approved by the provisions of a/an

Parts Manufacturer Approval

Cheating on an FAA exam may be tolerated if certain requirements are met and the FAA administrator is familiar with your limitations

false

What is the minimum passing grade of all FAA exams?

70%

Falsely reproducing aircraft records can result in ___

certificate suspension or revocation

The FAA requires a fixed base of operation for an inspection Authorization to be approved

true

A mechanic must hold their license for __ years to be eligible for an Inspection Authorization

The applicant form, to become a certified mechanic, is Form ___

8610-2

____ months of practical experience, working on aircraft, are required to apply for the airframe and powerplant certificate l, if the applicant has not attended a certified school

Maintenance managers, that request shortcuts to be made in repair or maintenance, will always stand by their requests under oath in court

false

An airframe and powerplant mechanic may perform, and return to service, a 100 hour inspection on an aircraft, propellor, and engine.

false

A powerplant mechanic may perform a major repair to an aircraft engine but a ___ is required to return it to service

Inspection Authorization (IA)

The recent experience requirements of the mechanics certificate may be fulfilled through supervising maintenance or alteration of aircraft.

true

Repairing an altimeter is a privilege of the airframe mechanic

false

Propeller knowledge and testing would be included in what rating?

powerplant

The mechanic ratings include the ____ and ____

airframe, powerplant

A certified mechanic must be at least __ years of age

Refusing to submit to drug and alcohol testing is ____

grounds for revoking their certificate

The FAA must be notified within ___ days of a change of address of any person holding a mechanic certificate

A mistake in recording the part number, is a part installed on an aircraft, if unintentional, is cause for revoking a mechanics certificate

false

The two methods by which an applicant for a mechanics certificate may retake a failed written test include _____ and _____

waiting 30 days, receive additional instruction with a signed statement

The mechanic certificate must be renewed each year or it will expire

false

If you ____ your mechanic certificate, this means you return it voluntarily

surrender

A conviction, for the sale of marijuana, may result in your mechanic certificate being suspended or revoked

true

The primary difference between the mechanic certificate and the repairman certificate is that the mechanic can perform more difficult repairs than the repairman.

false

The mechanic, and the repairman certificates are considered to be different classifications by the FAA

true

14 CFR Part 65 relates to the verification of airmen other than ___ crew members

flight

Simple or minor preservation operations and the replacement of small standard parts not involving complex assembly operations best describes:

preventative maintenance

An airframe certificated mechanic may perform the entire 100 hour inspection upon an aircraft and return it to service

false

Aircraft that operated under a progressive inspection program are required to undergo an annual inspection every year

false

If the holder of an inspection authorization changes his fixed base of operation,

To be elegible for a repairman cerficate (experimental aircraft builder) an individual must - Which of the following is not true

Be at least 16 years of age

1&2

Which of the following does not apply To be elegible for an inspection authorization, an applicant must-

pass a written test, oral test, and practical exam covering the construction and maintenance of aircraft

Each inspection authorization expires:

march 31st of each odd numbered year

A mechanic with only an airframe rating may obtain an inspection authorization valid only for the maintenance, inspection, repair, and alteration of the aircraft frame

false

The holder of an inspection authorization may supervise a progressive inspection

true

When a mechanic exercises the privileges of an inspection authorization he shall keep it available for inspection for which of the following:

all of the above

A certificated A&P mechanic may approve and return to service an airframe, powerplant, or propellor or any related part or appliance

after he has performed, supervised, or inspected a major repair or alteration for an aircraft in the light sport category

true

An A&P rated mechanic may do which of the following

supervise the maintenance, preventative maintenance or alteration of an aircraft or appliance

Which of the following does not apply