prior to corrosion removal, what must be determined

what is the next step after the plotter cuts your vinyl

which motion should you use when removing corrosion with a hand held wire brush

at a minimum, material data safety sheet are made available to

an individual item of supply that has an extendable shelf-life is considered type

after all visible corrosion is removed, how many additional mils should be removed

which formula would you use to determine maximum corrosion pit depth when using a dept gauge

the distance that you hold the spray gun nozzle from the surface depends upon the

an atom that has gained or lost electrons and has acquired and electrical charge is called

the four characteristics of hazardous waste are ignitableity, corrosivity, reactive, and

low viscosity CPC are best suited for what type of application

what effect does low humidity have on moisture curing coating

when preparing to mix a two-part sealant, you mix the sealant in according with the

material compatibility refers to using a medium that will

sealants that have a long work-life normally have a

the two categories that corrosion preventive coumpounds are separated into include

what will happe if two-component materials are not throughly mixed with each other and in the exact specified proportions

at is a common cause of streaking when spraying painting

when removing corrosion with pneumatic sander, how do you keep the sander from digging into the metal

metals such as stainless steel and titanium that corrode slowly are referred to as

the probable cause of a protective coating spray pattern with a split spray is

what percentage of low observable coatings must be separated as classified or unclassified prior to disposal

when painting, what must you do just prior to primer or topcoating

when using parallel strokes with a spray gun, the spray pattern should

what is the most common cause of coating failure

what type of spray gun is made with an external airtight container

when would an aircraft that took off four times over salt water require a clear water rinse

what do you use to fabricate a sealant removal tool

an individual item of supply that has a definite non-extendible period of shelf-life is considered type

what special requirements must be met when mechanically removing coatings on steel and titanium alloy

to clean dirt and grease from a surface to be sealed, you use

solid waste can be any material that is essentially waste-like, abandoned, or

when preforming a corrosion inspection, which tool would you use to dislodge blisters or bubbles

what is the first step in a general corrosion insp

90 day accumulation sites for haz waste containers should be able to contain the volume of

the type of chemical remover to be used depends on the

before applying an aerodynamic smoothing coumpound to repair seams

he purpose of adding pigment to paint is to develop

standards for paint such as color, drying time, and adhesion are stipulated by the

what is the last step in the general corrosion removal process

what conditions do you consider when you are choosing a cleaning method

what is the minimum number of readings you need to take when using a wet film gauge to measure coating thicknesses

when the TO calls for a permanent type of seal between two parts, you install a

the paint edges around the chemically stripped areas are feathered in order to

using a #2 zahn cup, how is the viscosity expressed

how often should haz waste containers be insp for release problems

on fixed-wing aircraft, the national star insignia is listed on the

what type of seal is produced by sandwiching sealant between mating surfaces

when should you dismantle a spray gun

what is the first step when preparing a part for blasting in the plastic meds blasting booth

pitting corrosion of aluminum or magnesium is first noticed as

what is their rate of corrosion when the anode is smaller, in relation to the cathode in the electrochemical corrosion cell

what is the coarsest grit of abrasive paper that should be used to scuff-sand an already coated aircrat

when using the plastic media blasting cabinet blaster, check the media level

corrosion in an electrochemical cell always starts an the

after checking the shelf life of your coating material you should

the method you use to remove excess aerodynamic smoothing compound from seams depends on the

which is not a reason for immediate cleaning

on a polished surface, uniform surface corrosion is first seen as

when do you mix chemical paint remover

sone metals have the ability to become electrochemically inactive or passive under certain conditions because of the formation of

when inspecting exhaust path.s for corrosion, what areas should be inspected because they cannot be reached with normal cleaning

corrosion that appears as blistering, exfoliation, and scaling or flaking is classified as