問題一覧
1
Which of the following is an acceptable distance for the opening between two adjacent platforms?
3 inches (76 mm)
2
The most common cause of playground fatalities?
Entanglement
3
When performing a safety audit a 5/8 inch, 16 mm diameter rod is used to check for:
a crush or shear hazard on a moving component
4
During a routine playground safety inspection a CPSI discovers “S” hooks connecting a belt swing that are showing 1/3 inch wear. When should the CPSI recommend replacement?
replace worn equipment parts following the manufacturer’s instructions as soon as possible, keep dated records of inspection and remedial actions taken.
5
When replacing S-hooks on swings, ASTM F1487 states that there shall be no gap greater than:
0.04 inches (1 mm)
6
How should the CPSI determine the impact attenuation of the poured-in-place safety surfacing when auditing a playground?
Verify the documentation from the manufacture.
7
Which of the following is the most important factor when determining placement of playground equipment for 2 to 5 year olds?
Circulation of users
8
The primary reason for adding protective barriers on composite structures is to prevent:
Deliberate attempt to pass through the device
9
A standard of care for playground equipment, and surfacing is achieved after:
All non-compliances identified have been remedied
10
What is the minimum use zone between a stand alone climber, and a standing-rocking-springing playground piece?
156 inches, (3962 mm )
11
The determination of what constitutes a playground hazard, according to the ASTM standards, and CPSC guidelines is derived from all of the following EXCEPT:
International playground equipment manufacturers association (IPEMA)
12
Which of the following statements regarding play equipment materials and manufacture is true?
Plastic material shall be protected from UV light
13
Which of the following elements should a CPSI incorporate into an effective playground safety inspection process. 1 - Inspection forms that document both problems and corrective actions. 2 - An approach to inspections and maintenance that is pro-active. 3 - A plan for taking equipment out of service that utilizes a variety of methods. 4 - Easy- to-use inspection forms based on the agency’s past accident experience.
1,2, and 3 only
14
What is the purpose of a playground safety audit?
Record compliance with current guidelines and standards.
15
Which of the following ASTM standards addresses fencing?
F2049
16
What establishes the public playground owner’s standard of care for the risk management program?
Safety policy
17
When evaluating the structure integrity of a support structure for a swing that appears to be failing , a CPSI should:
hire a licensed professional engineer to certify the integrity of the equipment.
18
Low-frequency inspection forms should be:
Assembled using information from the Site History File and Manufacturer’s recommendations.
19
Which of the following is appropriate if found in a 2 - 5 play area?
8’ high freestanding slide
20
Manufacturer’s of playground equipment must:
Provide the manufacturer’s identification on the equipment.
21
Which of the following ASTM documents should be used as a reference, when selecting a surfacing system to be installed in a public playgroun?
F2223
22
Many of the performance requirements related to slides do not apply to:
Embankment slides
23
Which of the following is correct regarding the impact-attenuation of surface material?
Critical height must equal or exceed fall height.
24
Which of the following has the greatest potential to create a Priority 1 hazard on a 120 inch (3050 mm) long embankment slide?
Slide shoot clearance zone less than 15 inches, (380 mm)
25
In a play area intended for 2 to 5 year old children which of the following platform heights would require a guard rail?
24 inches, (610 mm)
26
Regarding playground safety signage, which of the following is correct:
Signage may not prevent accidents, but may reduce the size of the rewards in liability lawsuits.
27
Which of the following noted during an examination of a neighborhood playground would be considered a Priority 1 safety concern:
A vertical projection extending 1/4 inch (6.4 mm) from the top rail of a swing support structure.
28
The ADA requires that all assessable equipment on new or renovated playgrounds must:
Be on an accessible route
29
One of the first pieces of playground equipment recommended to be removed for safety reasons was :
The giant stride
30
Which of the following is true when using flexible components as access to a platform:
A means of hand support during transition to the platform must be provided
31
A CPSI Audits a new playground design for children age 2-5 and documents all compliant and non-compliant conditions found. Which of the following is a non-compliant condition?
The playground contains a platform used to access a track ride that is 38 inches by 36 inches.
32
The Site History File for a playground should contain:
A comprehensive inventory of all equipment,a parts list, maintenance and inspection recommendations.
33
Which of the following cover selecting and specifying surface systems under and around playground equipment?
ASTM F2223
34
Which of the following statements about playground inspections is true?
High-frequency inspections should focus on routine maintenance.
35
The most common cause of injury on a public playground is :
Falls