記憶度
10問
27問
0問
0問
0問
アカウント登録して、解答結果を保存しよう
問題一覧
1
Based on PAES 212:2004, the minimum field efficiency for rice reaper is?
65%
2
Identify the classification of rubber roll for rice mill shown below
off centered
3
The rubber roll when tested in accordance to PAES 215 shall have hulling efficiency of at least
80%
4
Identify the classification of hammer mill (according to it's design) shown below
Fixed type
5
A classification system that indicates the uniformity of grind in the resultant product and is defined as the sum of the weight fractions retained above each sieve divided by 100.
Fineness modulus
6
A cylindrical roll generally with protrusions or flutes, used to gather, compress and advance the crop into the cutterhead
feedroll
7
Forage chopper which uses a feeding mechanism consisting of four or more feed rolls to partially orient and advance the crop at a consistent rate into the cutting mechanism
Precision-cut forage chopper
8
Type of forage chopper where the chopped materials are thrown away to the front area of the machine.
throw-away type
9
What is the minimum shelling recovery of a peanut sheller?
93%
10
Based on PAES 222:2005 A chip is a thin slice of material with thickness of about ?
4mm
11
. PAES 222:2005 Type of chipping machine with knives mounted radially with the cutting edges describing a plane perpendicular to the axis of rotation
flywheel type
12
It is the angle of the cutting edge of the blade of a chipping machine.
blade bevel angle
13
It is the angle of inclination of the blade with respect to the chipping plate.
rake angle
14
It is an auxiliary conveyor to assist in feeding the crop to the threshing cylinder in a rice combine
Crop elevator
15
Which type of rice combine is fitted with full or half tracks instead of pneumatic wheels?
track type
16
It is also called as "binlid"
brewers rice
17
Village model is a type of micromill with input capacity of?
100-250 kg/hr
18
The milled rice sample from the laboratory whitener shall be weighed and separated into components of?
all of the above
19
It is part of the decorticator where raw materials are beaten up and crushed.
scraper block
20
Which of the following has the highest fiber recovery wen using a decorticator?
ramie
21
It is the ratio of the amount between the total weight of the fiber extracted to the total amount of fiber content on a dry basis.
extraction efficiency
22
What is referred to as "copra"?.
Dried coconut meat from which oil is extracted
23
What is the minimum percent crude oil recovery of oil expeller?
60%
24
What is the maximum moisture content of copra that shall be used as a test material for oil expeller?
8%
25
What classification of a multicrop washer-peeler has an effective capacity of more than 15 kg/h up to 40 kg/h.
medium scale
26
Which of the following is not a rhizome?
cabbage
27
It is an aqueous liquid expressed or extracted from crops cells or tissues
juice
28
It is a type of extraction mechanism where the machine extract juice by squeezing or compressing. Crops are placed between two surfaces and subjected to pressure
piston press type
29
It refers to the physical and chemical properties of juice extracted.
juice quality
30
In which type of continuous flow dryer does the grain and drying air move in opposite directions?
counter-flow type
31
What does the term "moisture gradient" refer to in grain drying?
difference between the max and min grain moisture content
32
Which of the following does not belong to the group?
concurrent flow type dryer
33
Which of the following is considered as head rice?
3/4 of the average length of a whole grain
34
It is the ratio of the total heat utilized to vaporize moisture in the material, to the amount of heat added to the drying air expressed in percent
drying efficiency
35
Which of the following is a conventional energy source?
kerosene
36
How is heat utilization measured?
kilojoules per kilogram of h20
37
it is the process of holding the grain between the drying passes allowing moisture content in the center of the grain and that on the surface of the grain to equalize
Tempering
38
Milling test of the samples obtained during grain drying test shall be conducted at least hours after the drying test while air-dried samples shall be milled when its moisture content reaches 14%
48 hours
39
What is the targeted final moisture content for rice and corn after drying?
14%
40
Where should the air velocity in a dryer be measured during the test?
at the heat exchanger
41
Which technique is not used in the primary method of moisture determination?
electrical resistance
42
Based on PAES 204:2000 Mechanical Rice Thresher, what is the maximum mechanically damaged grain?
2%
43
Based on PAES 204:2000, the maximum allowable noise level for Mechanical Rice Thresher is
95 db
44
What is an axial flow thresher designed to do?
allow cut plants to move in a helical manner around the threshing cylinder
45
Which of the following is NOT a purpose of a concave grate in a thresher
to clean the cut plants
46
How is grain-straw ratio defined?
ratio of weight of grains to the total weight of grain and straw
47
What should be measured using a tachometer during the performance test of thresher?
speed of the threshing cylinder
48
it is a dehulled palay (husk/hull removed) with the bran layer still intact
brown rice
49
What is milled rice?
rice with both hull and bran removed
50
Which auxiliary device is used to give milled rice a glossy appearance?
Polisher
51
What distinguishes undermilled rice from well-milled rice?
Undermilled rice has more than 40% of grains with lengthwise streaks of the bran layer
52
What percentage of sample grains in regular milled rice may still have lengthwise streaks of the bran layers?
15% to 40%
53
Type of corn sheller wherein the ear corn are fed into shelling chamber with the application of external force.
Table-fed type
54
What is the minimum shelling recovery for corn sheller?
97%
55
What is referred to as shelled corn of either dent or flint varieties?
corn kernels
56
Milled corn kernels with particle size between 1.2 mm to 1.4 mm
grit #14
57
It is the major component of the corn mill used to reduce corn kernels into corn grits
roller mill
58
What is the minimum main product for corn mill?
64%
59
It is an auxiliary device of the corn mill that removes foreign material.
precleaner
60
Shape of a wing or blade of a propeller, rotor, or turbine or sails as seen in cross section
airfoil
61
PAES 240:2010. Type of driving mechanism that can obtain any fan/blower speed by controlling the pulley ratio.
belt-drive fab/blower
62
Which of the following is classification of an axial-flow fan?
tube-axial fan
63
Fire resistant surface located at the heating chamber of the biomass furnace.
hearth
64
Which of the following is not a direct- fired biomass furnace?
dry type
65
Biomass shredder that is installed permanently and commonly provided with adjustable anchors to level up the machine during operation.
stationary
66
these are fine and powder-like particles parenchymatous cells that are extracted from the coconut husk
coconut peat
67
Process of removing and separating the skin and pulp of coffee cherry.
pulping
68
Method that uses tuxying knife to thrust one side of the leaf sheath and make a cut between the upper and the inner portions of the material to be able to extract the tuxies
locnit method
69
Machine used to mix uniformly the feed ingredients.
feed mixer
70
What are chaffs in the context of threshing?
empty grains and crushed straw
71
It is the ratio of the weight of grains that come out of the threshing chamber with the straw, to the weight of total grain input of the thresher, expressed in percent.
seperation loss
72
What is the bran layer in brown rice?
the aleurone cells covering the endosperm