Problem_Solving_02 | 暗記メーカー

暗記メーカー

Problem_Solving_02

20問 • 1年前

Jacky Shane Luyas Buhia

問題一覧

1

The power required to shear a plate 50 mm thick for 10 seconds is 5 kW. If ultimate strength of plate material is 420 Mpa. How wide should the plate be ?

D. 95.23 mm

2

A car travels with an initial velocity of 10 m/s or 36 km/hr. If it is decelerating at the rate of 3 m/s², how far in meters does it travel before stopping?

A. 17

3

A block weighing 56 lbs rest on horizontal surface. The force needed to move along the surface is 20 lbs. Determine the coefficient of friction.

C. 0.36

4

A journal bearing with diameter of 76.2 mm is subjected to a load of 4900 N while rotating at 200 rpm. If it's coefficient of friction is 0.02 and L/D = 2.5, find its projected area in mm².

D. 14,516

5

A horizontal cantilever beam, 16 ft long is subjected to a load of 500 lb located to its center. The dimension of the beam is 2×4 inches respectively, w = 100 lb/ft, find its flexural stress

A. 3150 psi

6

A 10 m simply supported beam with uniform load of 3 kN/m from right end to left end has a maximum deflection of: ( El = 12,000 kN.m² )

B. 32.55 m

7

A 10 m cantilever beam has a concentrated load of 10 kN at the free end. Find the maximum deflection of the beam. ( El = 7,000 kN.m² )

A. 476.20 mm

8

A 14 m cantilever beam has a load of 16 kN 6 m from the fixed end. Find the maximum slope of the beam. (El = 6000 kN.m²)

B. 0.048 rad

9

What pressure is required for punching a hole 2 inches in diameter thru a 1/4 inch steel plate?

D. 40 tons

10

Compute how many 3/8 inch diameter set screws required to transmit 3 Hp at a shaft speed of 1000 rpm. The shaft diameter is 1 inch.

B. 2

11

What power would a short shaft, 50 mm in diameter, transmit at 400 rpm?

B. 60 kw

12

What would be the diameter of power-transmitting shaft to transmit 150 kw at 500 rpm?

B. 81 mm

13

If a cube of mass 200 kg is being moved on a conveyor belt at a speed of 3 m/s, what is the kinetic energy of the cube?

B. 900 J

14

A casting of mass 150 kg is lifted 4 meters in 15 seconds by means of a crane. What is the power?

A. 392 watts

15

What horsepower would be transmitted by a short shaft, 2 inches in diameter, carrying but two pulleys too close to bearings if the shaft makes 300 pm?

C. 63 hp

16

What force is necessary to punch a 30 mm hole in 12.5 mm thick plate if ultimate shear stress is 410 Mpa?

C. 483 KN

17

What force P is required to punch a 1/2 in. hole on a 3/8 in. thick plate. If the ultimate shear strength of the plate is 42,000 psi ?

D. 24 740 lbs

18

A cylindrical tank with 10 inches inside diameter contains oxygen gas at 2500 psi. Calculate the required wall thickness in millimeter under stress of 28000 psi.

B. 11.34

19

Compute the safe wall thickness of a 76.2 cm diameter steel tank. The tank is subjected to 7.33 Mpa pressure and the steel material has Yield stress of 215.4 Mpa. The factor of safety to use is 3.

B. 3.89 cm

20

A 3 in diameter short shaft carrying pulleys close to the bearings transmit how much horsepower if the shaft makes 280 rpm?

C. 199 hp

Weekly Test 1

Weekly Test 1

ユーザ名非公開 · 50問 · 13日前

Weekly Test 1

Weekly Test 1

50問 • 13日前

ユーザ名非公開

Refresher SPDI 1

Refresher SPDI 1

ユーザ名非公開 · 9問 · 13日前

Refresher SPDI 1

Refresher SPDI 1

9問 • 13日前

ユーザ名非公開

Definition of Terms 2

Definition of Terms 2

ユーザ名非公開 · 90問 · 13日前

Definition of Terms 2

Definition of Terms 2

90問 • 13日前

ユーザ名非公開

WT 2

WT 2

ユーザ名非公開 · 48問 · 13日前

WT 2

WT 2

48問 • 13日前

ユーザ名非公開

WT 1

WT 1

ユーザ名非公開 · 50問 · 13日前

WT 1

WT 1

50問 • 13日前

ユーザ名非公開

Item 311 Portland Cement Concrete Pavement (PART 1)

Item 311 Portland Cement Concrete Pavement (PART 1)

ユーザ名非公開 · 78問 · 13日前

Item 311 Portland Cement Concrete Pavement (PART 1)

Item 311 Portland Cement Concrete Pavement (PART 1)

78問 • 13日前

ユーザ名非公開

Item 311 Portland Cement Concrete Pavement (PART 2)

Item 311 Portland Cement Concrete Pavement (PART 2)

ユーザ名非公開 · 61問 · 13日前

Item 311 Portland Cement Concrete Pavement (PART 2)

Item 311 Portland Cement Concrete Pavement (PART 2)

61問 • 13日前

ユーザ名非公開

Item 406 Prestressed Concrete Structures

Item 406 Prestressed Concrete Structures

ユーザ名非公開 · 36問 · 13日前

Item 406 Prestressed Concrete Structures

Item 406 Prestressed Concrete Structures

36問 • 13日前

ユーザ名非公開

RNPCP Appendix A and B

RNPCP Appendix A and B

ユーザ名非公開 · 79問 · 13日前

RNPCP Appendix A and B

RNPCP Appendix A and B

79問 • 13日前

ユーザ名非公開

Item 303 Bituminous Seal Coat

Item 303 Bituminous Seal Coat

ユーザ名非公開 · 20問 · 13日前

Item 303 Bituminous Seal Coat

Item 303 Bituminous Seal Coat

20問 • 13日前

ユーザ名非公開

Item 301 Bituminous Prime Coat

Item 301 Bituminous Prime Coat

ユーザ名非公開 · 10問 · 13日前

Item 301 Bituminous Prime Coat

Item 301 Bituminous Prime Coat

10問 • 13日前

ユーザ名非公開

Item 300 Aggregate Surface Course

Item 300 Aggregate Surface Course

ユーザ名非公開 · 11問 · 13日前

Item 300 Aggregate Surface Course

Item 300 Aggregate Surface Course

11問 • 13日前

ユーザ名非公開

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

ユーザ名非公開 · 11問 · 13日前

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

Item 206 Chemically Stabilized Road Mix Subbase/Base Course

11問 • 13日前

ユーザ名非公開

Item 205 Asphalt Stabilized Road Mix Base Course

Item 205 Asphalt Stabilized Road Mix Base Course

ユーザ名非公開 · 7問 · 13日前

Item 205 Asphalt Stabilized Road Mix Base Course

Item 205 Asphalt Stabilized Road Mix Base Course

7問 • 13日前

ユーザ名非公開

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

ユーザ名非公開 · 13問 · 13日前

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

Item 207 Portland Cement Stabilized Treated Plant Mix Base Course

13問 • 13日前

ユーザ名非公開

Item 204 Portland Cement Stabilized Road Mix Base Course

Item 204 Portland Cement Stabilized Road Mix Base Course

ユーザ名非公開 · 7問 · 13日前

Item 204 Portland Cement Stabilized Road Mix Base Course

Item 204 Portland Cement Stabilized Road Mix Base Course

7問 • 13日前

ユーザ名非公開

Item 203 Lime Stabilized Road Mix Base Course

Item 203 Lime Stabilized Road Mix Base Course

ユーザ名非公開 · 27問 · 13日前

Item 203 Lime Stabilized Road Mix Base Course

Item 203 Lime Stabilized Road Mix Base Course

27問 • 13日前

ユーザ名非公開

Item 202 Crushed Aggregate Base Course

Item 202 Crushed Aggregate Base Course

ユーザ名非公開 · 18問 · 13日前

Item 202 Crushed Aggregate Base Course

Item 202 Crushed Aggregate Base Course

18問 • 13日前

ユーザ名非公開

Item 201 Aggregate Base Course

Item 201 Aggregate Base Course

ユーザ名非公開 · 16問 · 13日前

Item 201 Aggregate Base Course

Item 201 Aggregate Base Course

16問 • 13日前

ユーザ名非公開

Item 200 Aggregate Subbase Course

Item 200 Aggregate Subbase Course

ユーザ名非公開 · 16問 · 13日前

Item 200 Aggregate Subbase Course

Item 200 Aggregate Subbase Course

16問 • 13日前

ユーザ名非公開

問題一覧

1

The power required to shear a plate 50 mm thick for 10 seconds is 5 kW. If ultimate strength of plate material is 420 Mpa. How wide should the plate be ?

D. 95.23 mm

2

A car travels with an initial velocity of 10 m/s or 36 km/hr. If it is decelerating at the rate of 3 m/s², how far in meters does it travel before stopping?

A. 17

3

A block weighing 56 lbs rest on horizontal surface. The force needed to move along the surface is 20 lbs. Determine the coefficient of friction.

C. 0.36

4

A journal bearing with diameter of 76.2 mm is subjected to a load of 4900 N while rotating at 200 rpm. If it's coefficient of friction is 0.02 and L/D = 2.5, find its projected area in mm².

D. 14,516

5

A horizontal cantilever beam, 16 ft long is subjected to a load of 500 lb located to its center. The dimension of the beam is 2×4 inches respectively, w = 100 lb/ft, find its flexural stress

A. 3150 psi

6

A 10 m simply supported beam with uniform load of 3 kN/m from right end to left end has a maximum deflection of: ( El = 12,000 kN.m² )

B. 32.55 m

7

A 10 m cantilever beam has a concentrated load of 10 kN at the free end. Find the maximum deflection of the beam. ( El = 7,000 kN.m² )

A. 476.20 mm

8

A 14 m cantilever beam has a load of 16 kN 6 m from the fixed end. Find the maximum slope of the beam. (El = 6000 kN.m²)

B. 0.048 rad

9

What pressure is required for punching a hole 2 inches in diameter thru a 1/4 inch steel plate?

D. 40 tons

10

Compute how many 3/8 inch diameter set screws required to transmit 3 Hp at a shaft speed of 1000 rpm. The shaft diameter is 1 inch.

B. 2

11

What power would a short shaft, 50 mm in diameter, transmit at 400 rpm?

B. 60 kw

12

What would be the diameter of power-transmitting shaft to transmit 150 kw at 500 rpm?

B. 81 mm

13

If a cube of mass 200 kg is being moved on a conveyor belt at a speed of 3 m/s, what is the kinetic energy of the cube?

B. 900 J

14

A casting of mass 150 kg is lifted 4 meters in 15 seconds by means of a crane. What is the power?

A. 392 watts

15

What horsepower would be transmitted by a short shaft, 2 inches in diameter, carrying but two pulleys too close to bearings if the shaft makes 300 pm?

C. 63 hp

16

What force is necessary to punch a 30 mm hole in 12.5 mm thick plate if ultimate shear stress is 410 Mpa?

C. 483 KN

17

What force P is required to punch a 1/2 in. hole on a 3/8 in. thick plate. If the ultimate shear strength of the plate is 42,000 psi ?

D. 24 740 lbs

18

A cylindrical tank with 10 inches inside diameter contains oxygen gas at 2500 psi. Calculate the required wall thickness in millimeter under stress of 28000 psi.

B. 11.34

19

Compute the safe wall thickness of a 76.2 cm diameter steel tank. The tank is subjected to 7.33 Mpa pressure and the steel material has Yield stress of 215.4 Mpa. The factor of safety to use is 3.

B. 3.89 cm

20

A 3 in diameter short shaft carrying pulleys close to the bearings transmit how much horsepower if the shaft makes 280 rpm?

C. 199 hp