M7C7

19問 • 2ヶ月前

ユーザ名非公開

通報

問題一覧

is the electrical interconnection of all metal parts of an aircraft,

Bonding

Bonding is the electrical interconnection of all metal parts of an aircraft to

Reduces radio

Megger tester is

Battery Operated device

Crimping checked for mechanical security by

pull-off checks

What gauge of pin would a yellow plastic insert/extract tool be used on?

12-10

The hole is placed in the lowest point of electrical cable conduit:

to allow for drainage of moisture

What is Wet Arc Tracking :

a fault caused by insulation damage

When using a heat shrink gun; the temperature of the gun should be set to:

100 degree above the heat shrink temperature.

In the Selection of Heat Shrinkable Sleeving the type applied depends on:

A-Flexibility required B- Vibration suffered

The Pulse width of TDR is 2 nanosecond the blind spot length of twisted pair and coaxial is

6ft,2m

On a coaxial cable, cable impedance is

not effected by the length of the cable

Co-axial cable is preferred to airframe cable in witch application?

Where the diameter of cable is not important.

With a rear release connector the pin will be:

released from the rear and extracted From the rear

To carry out Insulation test on a wire rated 115 volts the test voltage should be minimum of

250 Volts

If an aircraft wire bundle must run near fuel , oil or hydraulic lines then the wire bundles should be secured :

above the fluid line

Tin plated copper maximum continuous temperature is:

260 degrees centigrade

The Display rate of a digital multimeter is

the number of time per second that the meter takes measurement

a 3½-digit meter displays up to

1,999 counts of resolution.

Note: Even when testing very long lengths of coaxial cable, always start the fault finding procedure in

the shortest pulse width

module 1 ch1

ユーザ名非公開 · 53問 · 11ヶ月前

module 1 ch1

53問 • 11ヶ月前

ユーザ名非公開

ユーザ名非公開 · 68問 · 11ヶ月前

68問 • 11ヶ月前

ユーザ名非公開

ユーザ名非公開 · 68問 · 11ヶ月前

m4 ch 2

m4 ch 2

m4 ch 3

m4 ch 3

m 4 ch 4

m 4 ch 4

M15c1

M15c1

M15c2

M15c2

M15c3

M15c3

M15c4

M15c4

M15c3

M15c3

M15c4

M15c4

M15c5

M15c5

M15c6

M15c6

M7c1

M7c1

M7c2

M7c2

M7c3

M7c3

M7c3

M7c3

M7c4

M7c4

問題一覧

is the electrical interconnection of all metal parts of an aircraft,

Bonding

Bonding is the electrical interconnection of all metal parts of an aircraft to

Reduces radio

Megger tester is

Battery Operated device

Crimping checked for mechanical security by

pull-off checks

What gauge of pin would a yellow plastic insert/extract tool be used on?

12-10

The hole is placed in the lowest point of electrical cable conduit:

to allow for drainage of moisture

What is Wet Arc Tracking :

a fault caused by insulation damage

When using a heat shrink gun; the temperature of the gun should be set to:

100 degree above the heat shrink temperature.

In the Selection of Heat Shrinkable Sleeving the type applied depends on:

A-Flexibility required B- Vibration suffered

The Pulse width of TDR is 2 nanosecond the blind spot length of twisted pair and coaxial is

6ft,2m

On a coaxial cable, cable impedance is

not effected by the length of the cable

Co-axial cable is preferred to airframe cable in witch application?

Where the diameter of cable is not important.

With a rear release connector the pin will be:

released from the rear and extracted From the rear

To carry out Insulation test on a wire rated 115 volts the test voltage should be minimum of

250 Volts

If an aircraft wire bundle must run near fuel , oil or hydraulic lines then the wire bundles should be secured :

above the fluid line

Tin plated copper maximum continuous temperature is:

260 degrees centigrade

The Display rate of a digital multimeter is

the number of time per second that the meter takes measurement

a 3½-digit meter displays up to

1,999 counts of resolution.

Note: Even when testing very long lengths of coaxial cable, always start the fault finding procedure in

the shortest pulse width