暗記メーカー

暗記メーカー

​
ログイン

test

test
86問 • 1年前
  • Sandra Salazar
    • 通報

    問題一覧

  • 1

    ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED FOR A 3/4" DIAMETER BOLT?

    2 1/4"

  • 2

    THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE?

    SPAN

  • 3

    BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE COMPLETED?

    JOIST MUST HAVE BRIDGING

  • 4

    WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO?

    HELP CONTROL THE LOAD

  • 5

    ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY FOUND ON:

    THE DETAIL DRAWINGS

  • 6

    THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS?

    A.TENSILE STRENGTH A.COMPRESSIVE STRENGTH

  • 7

    WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB?

    COMPOSITE DECK

  • 8

    THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION?

    30'3"

  • 9

    ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY FOUND ON:

    DETAIL DRAWINGS

  • 10

    WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH?

    STRIKER

  • 11

    EQUALIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED?

    A.CONFIGURATION A.BALANCING

  • 12

    PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD?

    PING TEST

  • 13

    A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT:

    A.45 DEGREE LINES A.85 DEGREE LINE

  • 14

    WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT?

    THE FRONT AXLE

  • 15

    A DOCUMENT THAT OUTLINES WEIGHTS, CRANE CONFIGURATION AND RIGGING REQUIREMENTS FOR A LIFT IS CALLED AN?

    LIFT PLAN

  • 16

    WHERE CAN THE BOLTING REGARDING STRUCTURAL STEEL USUALLY BE FOUND?

    IN THE GENERAL NOTES OF THE STRUCTURAL DRAWING

  • 17

    WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT USED TO DETERMINE ALL OTHER ELEVATIONS IS CALLED?

    THE BENCHMARK

  • 18

    WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE?

    183FT

  • 19

    MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS OF ROTATION TO THE CENTER OF THE LOAD LINE WITH THE LOAD APPLIED IS?

    LOAD RADIUS

  • 20

    WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO PRY STEEL INTO PLACE?

    SLEEVER BAR

  • 21

    WHEN TRAVELING TO PICK UP A LOAD, ALWAYS KEEP THE?

    FORKS LOW

  • 22

    WHAT TYPE OF DRAWING SHOWS THE PRECISE DIMENSIONS OF A SECTION OR PART OF THE LONGER PART?

    DETAIL

  • 23

    WHAT IS THE PROPER WAT TO ATTACH TWO SLINGS TOGETHER?

    USE A SHACKLE

  • 24

    HOW MANY PIECES OF CHECKERED PLATE CAN BE LIFTED WHEN USING PLATE GRABS?

    NO MORE THAN ONE

  • 25

    THE ACETYLENE STATIC PRESSURE SHOULD NOT RISE ABOVE:

    15PSIG

  • 26

    WHAT IS THE MAXIMUM ALLOWABLE DEVIATION FROM A PLUMB LINE FOR A SINGLE - COLUMN SHIPPING PIECE?

    1/1500

  • 27

    THE PROCESS OF STACKING TIMBERS IN ALTERNATE TIERS TO SUPPORT A HEAVY WEIGHT IS CALLED?

    BLOCKING

  • 28

    PLUMBING UP GUYS SHOULD BE INSTALLED TO PLUMB UP A STRUCTURE AFTER?

    ALL STEEL IS ERECTED

  • 29

    WHAT IS THE SURFACE AREA OF A TRIANGLE WITH A 12" BASE AND 10" HEIGHT?

    60IN SQUARE

  • 30

    SKIDMORE TESTER IS A DEVICE THAT MEASURES A BOLTS?

    YIELD PRESSURE

  • 31

    EXTENDABLE ARMS ATTACHED TO A CRANE BASE MOUNTING THAT RELIEVE THE WHEELS OF CRANE WEIGHT AND PROVIDE STABILITY ARE CALLED?

    OUTRIGGERS

  • 32

    WHICH OF THE FOLLOWING ITEMS ARE USED FOR HEAVY RIGGING?

    SLINGS, SHACKLES, AND SPREADER BEAM

  • 33

    WHAT IS USED TO PREVENT JOIST FROM MOVING LATERALLY?

    X-BRIDGING

  • 34

    RESPIRATORS SHOULD BE USED IF WELDING?

    IN A CONFINED SPACE

  • 35

    ALL THE FOLLOWING ACTIONS MAY SHORTEN THE SERVICE LIFE OF A WIRE ROPE EXCEPT?

    LUBRICATING THE ROPE

  • 36

    WHAT DOES MSDS STAND FOR?

    SAFETY DATA SHEET

  • 37

    ALL OF THE FOLOWING ARE TRUE ABOUT THE SAFE USE OF SHACKLES ЕХСЕРТ?

    SCREW PINS SHOULD BE BACKED OFF TWO TURNS

  • 38

    WHY MUST THE CYLINDER VALVE BE "CRACKED" BEFORE A REGULATOR IS CONNECTED TO AN OXYACETYLENE CYLINDER?

    TO CLEAN THE CYLINDER VALVE OF FOREIGN MATERIAL

  • 39

    WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO ALIGN BOLT HOLES?

    BULL PIN

  • 40

    WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE?

    VERTICLE ALIGNMENT POSITIONER

  • 41

    HOW IS THE SIZE OF THE CUTTING TORCH TIP DETERMINED?

    FROM THE BASE METAL THICKNESS AND FUEL TYPE BEING USED

  • 42

    JOIST ARE SUPPORTED LATERALLY BY?

    HORIZONTAL BRIDGING A.VERTICAL CHORDS

  • 43

    AN IRONWORKER SHOULD NOT SET A GRINDER DOWN WHEN THE DISK?

    IS STILL TURNING

  • 44

    STORED OXYFUEL CYLINDERS MUST BE SEPERATED BY A 30 MINUTE BURN WALL OR A DISTANCE OF AT LEAST?

    20'

  • 45

    A LOAD BLOCK IS?

    A BLOCK OF STEEL USED AS COUNTERWEIGHT

  • 46

    HAWG WASH IS A TYPE OF?

    LUBRICANT

  • 47

    A WELDING ELECTRODE MARKED AS E7018 CAN BE USED TO WELD?

    IN ALL POSITIONS

  • 48

    JOIST RESTING ON STEEL MUST HAVE A MINIMUM BEARING OF?

    1’IN

  • 49

    WHAT IS THE MINIMUM WAITING PERIOD BEFORE USING AN ACETYLENE CYLINDER THAT HAS TIPPED OVER?

    30 MINUTES

  • 50

    ONE OF THE LIMIT SWITCHES ON A CRANE IS CALLED A(N)?

    ANTI TWO BLOCKING DEVICE

  • 51

    ACETYLENE GAS REGUATORS ARE ALWAYS REDLINED AT?

    15 PSI

  • 52

    REMOVING A PORTION OF THE FLANGES AT THE END OF A BEAM TO ALLOW CONNECTION OF A BEAM TO THE WEB OF A COLUMN IS CALLED?

    COPING

  • 53

    THE RELATIONSHIP BETWEEN THE SHEAVE DIAMETER AND THE ROPE DIAMETER IS DESCRIBING THE?

    D:D RATIO

  • 54

    ALL OF THE FOLLOWING CONDITIONS WOULD REQUIRE THE REMOVAL OF RIGGING FROM SERVICE EXCEPT?

    EXCESSIVE LUBRICATION

  • 55

    IN CRANE OPERATIONS, WHAT IS A JIB?

    AN EXTENSION OF THE MAIN BOOM

  • 56

    THE MINIMUM LEVEL OF PPE THAT IS REQUIRED FOR A SPECIFIC TASK IS DETEMINED BY?

    THE COMPANY SAFETY DEPARTMENT

  • 57

    WHICH OF THE FOLLOWING IS NOT A TYPE OF DECKING?

    CELLULAR DECK

  • 58

    WHICH OF THE FOLLOWING BOLT TYPES IS KNOWN AS A "SOFT" BOLT THAT IS GENERALLY USED IN STATIC LOAD STRUCTURES?

    A307

  • 59

    WHEN MAINTAINING A SAFE WORK AREA, WHAT IS MOST IMPORTANT?

    GOOD HOUSEKEEPING

  • 60

    WHEN STACKING OR STORING JOIST, DUNNAGE OR CRIBBING SHOULD BE PLACED UNDER THE?

    LATERAL ENDS

  • 61

    WHEN STACKING OR STORING JOIST, DUNNAGE, OR CRIBBING SHOULD BE PLACED UNDER THE?

    LATERAL ENDS

  • 62

    WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE?

    VERTICLE ALIGNMENT POSITIONER

  • 63

    WHICH OF THE FOLLOWING CRANES ARE BEST SUITED FOR PICK AND CARRY OPERATIONS?

    CRAWLER CRANES

  • 64

    A DIE USED FOR CLEANING OR REPAIRING THREADS ON A ANCHOR ROD OR BOLT IS CALLED A?

    THREAD CHASER

  • 65

    THE ACCURACY OF A PLUMB BOB THAT IS BEING USED OUTSIDE MAY BE AFFECTED BY?

    WIND

  • 66

    WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS?

    CENTER OF GRAVITY

  • 67

    WHERE DOES THE FLUX COME FROM ON A SHEAR STUD?

    NIPPLE ON THE BOTTOM OF THE STUD

  • 68

    WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN STRUCTURAL STEEL APPLICATIONS?

    OXY-ACETYLENE WELDING

  • 69

    WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE MEASUREMENT INSTUMENT?

    LASER LIGHT

  • 70

    WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE CONSTRUCTION SHEAR STUDS?

    GTAW

  • 71

    BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN?

    PROPERLY TESTED AND STAMPED

  • 72

    WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT?

    TWISTING OF THE BUNDLE

  • 73

    IN ORDER TO WELD ON A JOBSITE A PERSON MUST?

    PASS A WELDING PERFORMANCE TEST

  • 74

    WHAT IS AN A-490 BOLT ?

    HIGH STRENGTH BOLT

  • 75

    A CRITICAL LIFT PLAN INCLUDES ALL THE FOLLOWING INFORMATION EXECEPT?

    THE NUMBER OF THE SUPERVISORS

  • 76

    WHICH SLING CONFIGURATION HAS THE GREASTEST CAPACITY?

    BASKET

  • 77

    CRANE MUST BE ASSEMBLED ACCORDING TO?

    THE MANUFACTURER’S INSTRUCTION

  • 78

    WHAT IS A GFCI?

    GROUND FAUIT CIRCUIT INTERRUMPTER

  • 79

    A SPECIAL BOLT THAT A SNAP-OFF SPINE IS A?

    TENSION/CONTROL BOLT

  • 80

    A SOLID FLAGIN A WELDING SYMBOL INDICATES THAT THE WELD IS TO BE PREFORMED?

    IN THE FEILD

  • 81

    SHACKELS SHOULD BE REPLACED WHEN THE CROWNS OR PINS ARE WORN BY MORE THAN?

    10%

  • 82

    THE TWO LEGS FORMING A CHOK NATRURALLY LIFTING TO PROXIMITY WHAT DEGREE ANGLE?

    45

  • 83

    A COMBINATION SQUARE WITHOUT A PROTECTOR HEAD IS A BLIND TO LAYOUT?

    85 DEGREE LINE

  • 84

    A TORQUE WRENCH MESSUAREMENT?

    RESISTANT TO TURNING

  • 85

    WHEN USING A MAGNETIC ____ THE POWER SOURCE SHOULD BE TAGGED.

    ALL THE PLUG

  • 86

    WHO IS THE RESPONSIBILITY FOR?

    EVERYONE

    • 問題一覧

  • 1

    ASSUMING A GRIP DISTANCE OF 1", WHAT IS THE MINIMUN LENGTH OF THE BOLT REQUIRED FOR A 3/4" DIAMETER BOLT?

    2 1/4"

  • 2

    THE LOCATION OF BRIDGING DEPENDS ON THE LENGTH OF THE?

    SPAN

  • 3

    BEFORE BUNDLES OF DECK CAN BE LANDED ON A BAR JOIST, WHAT ACTION MUST BE COMPLETED?

    JOIST MUST HAVE BRIDGING

  • 4

    WHEN MATERIALS ARE BEING HOISTED TO AN UPPER LEVEL, A TAG LINE IS USED TO?

    HELP CONTROL THE LOAD

  • 5

    ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY FOUND ON:

    THE DETAIL DRAWINGS

  • 6

    THE ABILITY OF A STRUCTURAL STEEL COMPONENT TO RESIST PULLING FORCES IS KNOWN AS?

    A.TENSILE STRENGTH A.COMPRESSIVE STRENGTH

  • 7

    WHAT TYPE OF DECKING HAS IMPRESSIONS FORMED ON ITS RIB?

    COMPOSITE DECK

  • 8

    THE GROUND FLOOR ELEVATION IS SHOWN AS +100.25. THE ROOF TOP ELEVATION IS SHOWN AS +130.50. WHAT IS THE DIFFERENCE IN ELEVATION?

    30'3"

  • 9

    ITEMS SUCH AS FIELD WELDING INSTRUCTIONS, HANGERS, AND CONNECTION DETAILS ARE GENERALLY FOUND ON:

    DETAIL DRAWINGS

  • 10

    WHAT SHOULD ALWAYS BE USED TO IGNITE A CUTTING TORCH?

    STRIKER

  • 11

    EQUALIZING THE WEIGHT OF THE LOAD AT VARIOUS LIFTING POINTS IS CALLED?

    A.CONFIGURATION A.BALANCING

  • 12

    PRIOR TO INSPECTION IT IS GOOD PRACTICE TO TEST ALL STUDS WITH WHAT METHOD?

    PING TEST

  • 13

    A COMBINATION SQUARE WITHOUT A PROTRACTOR HEAD IS USED TO LAYOUT:

    A.45 DEGREE LINES A.85 DEGREE LINE

  • 14

    WHERE IS THE FULCRUM OR PIVOT POINT ON A FORKLIFT?

    THE FRONT AXLE

  • 15

    A DOCUMENT THAT OUTLINES WEIGHTS, CRANE CONFIGURATION AND RIGGING REQUIREMENTS FOR A LIFT IS CALLED AN?

    LIFT PLAN

  • 16

    WHERE CAN THE BOLTING REGARDING STRUCTURAL STEEL USUALLY BE FOUND?

    IN THE GENERAL NOTES OF THE STRUCTURAL DRAWING

  • 17

    WHEN ESTABLISHING ELEVATIONS OF STRUCTURAL STEEL MEMBERS, THE REFERENCE POINT USED TO DETERMINE ALL OTHER ELEVATIONS IS CALLED?

    THE BENCHMARK

  • 18

    WHAT IS THE SURFACE AREA OF A RECTANGLE WITH THE DIMENSIONS OF 30'6" TALL AND 6 FEET WIDE?

    183FT

  • 19

    MEASUREMENTS FROM THE CENTER OF THE CRANES AXIS OF ROTATION TO THE CENTER OF THE LOAD LINE WITH THE LOAD APPLIED IS?

    LOAD RADIUS

  • 20

    WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO PRY STEEL INTO PLACE?

    SLEEVER BAR

  • 21

    WHEN TRAVELING TO PICK UP A LOAD, ALWAYS KEEP THE?

    FORKS LOW

  • 22

    WHAT TYPE OF DRAWING SHOWS THE PRECISE DIMENSIONS OF A SECTION OR PART OF THE LONGER PART?

    DETAIL

  • 23

    WHAT IS THE PROPER WAT TO ATTACH TWO SLINGS TOGETHER?

    USE A SHACKLE

  • 24

    HOW MANY PIECES OF CHECKERED PLATE CAN BE LIFTED WHEN USING PLATE GRABS?

    NO MORE THAN ONE

  • 25

    THE ACETYLENE STATIC PRESSURE SHOULD NOT RISE ABOVE:

    15PSIG

  • 26

    WHAT IS THE MAXIMUM ALLOWABLE DEVIATION FROM A PLUMB LINE FOR A SINGLE - COLUMN SHIPPING PIECE?

    1/1500

  • 27

    THE PROCESS OF STACKING TIMBERS IN ALTERNATE TIERS TO SUPPORT A HEAVY WEIGHT IS CALLED?

    BLOCKING

  • 28

    PLUMBING UP GUYS SHOULD BE INSTALLED TO PLUMB UP A STRUCTURE AFTER?

    ALL STEEL IS ERECTED

  • 29

    WHAT IS THE SURFACE AREA OF A TRIANGLE WITH A 12" BASE AND 10" HEIGHT?

    60IN SQUARE

  • 30

    SKIDMORE TESTER IS A DEVICE THAT MEASURES A BOLTS?

    YIELD PRESSURE

  • 31

    EXTENDABLE ARMS ATTACHED TO A CRANE BASE MOUNTING THAT RELIEVE THE WHEELS OF CRANE WEIGHT AND PROVIDE STABILITY ARE CALLED?

    OUTRIGGERS

  • 32

    WHICH OF THE FOLLOWING ITEMS ARE USED FOR HEAVY RIGGING?

    SLINGS, SHACKLES, AND SPREADER BEAM

  • 33

    WHAT IS USED TO PREVENT JOIST FROM MOVING LATERALLY?

    X-BRIDGING

  • 34

    RESPIRATORS SHOULD BE USED IF WELDING?

    IN A CONFINED SPACE

  • 35

    ALL THE FOLLOWING ACTIONS MAY SHORTEN THE SERVICE LIFE OF A WIRE ROPE EXCEPT?

    LUBRICATING THE ROPE

  • 36

    WHAT DOES MSDS STAND FOR?

    SAFETY DATA SHEET

  • 37

    ALL OF THE FOLOWING ARE TRUE ABOUT THE SAFE USE OF SHACKLES ЕХСЕРТ?

    SCREW PINS SHOULD BE BACKED OFF TWO TURNS

  • 38

    WHY MUST THE CYLINDER VALVE BE "CRACKED" BEFORE A REGULATOR IS CONNECTED TO AN OXYACETYLENE CYLINDER?

    TO CLEAN THE CYLINDER VALVE OF FOREIGN MATERIAL

  • 39

    WHICH OF THE FOLLOWING TOOLS WOULD BE USED TO ALIGN BOLT HOLES?

    BULL PIN

  • 40

    WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE?

    VERTICLE ALIGNMENT POSITIONER

  • 41

    HOW IS THE SIZE OF THE CUTTING TORCH TIP DETERMINED?

    FROM THE BASE METAL THICKNESS AND FUEL TYPE BEING USED

  • 42

    JOIST ARE SUPPORTED LATERALLY BY?

    HORIZONTAL BRIDGING A.VERTICAL CHORDS

  • 43

    AN IRONWORKER SHOULD NOT SET A GRINDER DOWN WHEN THE DISK?

    IS STILL TURNING

  • 44

    STORED OXYFUEL CYLINDERS MUST BE SEPERATED BY A 30 MINUTE BURN WALL OR A DISTANCE OF AT LEAST?

    20'

  • 45

    A LOAD BLOCK IS?

    A BLOCK OF STEEL USED AS COUNTERWEIGHT

  • 46

    HAWG WASH IS A TYPE OF?

    LUBRICANT

  • 47

    A WELDING ELECTRODE MARKED AS E7018 CAN BE USED TO WELD?

    IN ALL POSITIONS

  • 48

    JOIST RESTING ON STEEL MUST HAVE A MINIMUM BEARING OF?

    1’IN

  • 49

    WHAT IS THE MINIMUM WAITING PERIOD BEFORE USING AN ACETYLENE CYLINDER THAT HAS TIPPED OVER?

    30 MINUTES

  • 50

    ONE OF THE LIMIT SWITCHES ON A CRANE IS CALLED A(N)?

    ANTI TWO BLOCKING DEVICE

  • 51

    ACETYLENE GAS REGUATORS ARE ALWAYS REDLINED AT?

    15 PSI

  • 52

    REMOVING A PORTION OF THE FLANGES AT THE END OF A BEAM TO ALLOW CONNECTION OF A BEAM TO THE WEB OF A COLUMN IS CALLED?

    COPING

  • 53

    THE RELATIONSHIP BETWEEN THE SHEAVE DIAMETER AND THE ROPE DIAMETER IS DESCRIBING THE?

    D:D RATIO

  • 54

    ALL OF THE FOLLOWING CONDITIONS WOULD REQUIRE THE REMOVAL OF RIGGING FROM SERVICE EXCEPT?

    EXCESSIVE LUBRICATION

  • 55

    IN CRANE OPERATIONS, WHAT IS A JIB?

    AN EXTENSION OF THE MAIN BOOM

  • 56

    THE MINIMUM LEVEL OF PPE THAT IS REQUIRED FOR A SPECIFIC TASK IS DETEMINED BY?

    THE COMPANY SAFETY DEPARTMENT

  • 57

    WHICH OF THE FOLLOWING IS NOT A TYPE OF DECKING?

    CELLULAR DECK

  • 58

    WHICH OF THE FOLLOWING BOLT TYPES IS KNOWN AS A "SOFT" BOLT THAT IS GENERALLY USED IN STATIC LOAD STRUCTURES?

    A307

  • 59

    WHEN MAINTAINING A SAFE WORK AREA, WHAT IS MOST IMPORTANT?

    GOOD HOUSEKEEPING

  • 60

    WHEN STACKING OR STORING JOIST, DUNNAGE OR CRIBBING SHOULD BE PLACED UNDER THE?

    LATERAL ENDS

  • 61

    WHEN STACKING OR STORING JOIST, DUNNAGE, OR CRIBBING SHOULD BE PLACED UNDER THE?

    LATERAL ENDS

  • 62

    WHAT IS THE COMPONENT THAT ALLOWS A TRANSIT TO BE LINED UP OVE A REFERENCE POINT BY LOOKING THROUGH AN EYE PIECE?

    VERTICLE ALIGNMENT POSITIONER

  • 63

    WHICH OF THE FOLLOWING CRANES ARE BEST SUITED FOR PICK AND CARRY OPERATIONS?

    CRAWLER CRANES

  • 64

    A DIE USED FOR CLEANING OR REPAIRING THREADS ON A ANCHOR ROD OR BOLT IS CALLED A?

    THREAD CHASER

  • 65

    THE ACCURACY OF A PLUMB BOB THAT IS BEING USED OUTSIDE MAY BE AFFECTED BY?

    WIND

  • 66

    WHEN AN EXTENSION BOOM IS USED ON A FORKLIFT IT CHANGES ITS?

    CENTER OF GRAVITY

  • 67

    WHERE DOES THE FLUX COME FROM ON A SHEAR STUD?

    NIPPLE ON THE BOTTOM OF THE STUD

  • 68

    WHICH OF THE FOLLOWING WELDING PROCESSES IS NOT TYPICALLY USED IN STRUCTURAL STEEL APPLICATIONS?

    OXY-ACETYLENE WELDING

  • 69

    WHICH OF THE FOLLOWING IS A COMMON TYPE OF ELECTRONIC DISTANCE MEASUREMENT INSTUMENT?

    LASER LIGHT

  • 70

    WHAT STUD WELDING PROCESS IS USED TO INSTALL COMPOSITE CONSTRUCTION SHEAR STUDS?

    GTAW

  • 71

    BEFORE SPREADER BAR OR BEAMS CAN BE USED, THEY MUST HAVE BEEN?

    PROPERLY TESTED AND STAMPED

  • 72

    WHEN USING TWO SLINGS TO HOIST A BUNDLE OF LIGHT STEEL MATERIAL, THE SLINGS SHOULD BE LOOPED IN THE SAME DIRECTION TO PREVENT?

    TWISTING OF THE BUNDLE

  • 73

    IN ORDER TO WELD ON A JOBSITE A PERSON MUST?

    PASS A WELDING PERFORMANCE TEST

  • 74

    WHAT IS AN A-490 BOLT ?

    HIGH STRENGTH BOLT

  • 75

    A CRITICAL LIFT PLAN INCLUDES ALL THE FOLLOWING INFORMATION EXECEPT?

    THE NUMBER OF THE SUPERVISORS

  • 76

    WHICH SLING CONFIGURATION HAS THE GREASTEST CAPACITY?

    BASKET

  • 77

    CRANE MUST BE ASSEMBLED ACCORDING TO?

    THE MANUFACTURER’S INSTRUCTION

  • 78

    WHAT IS A GFCI?

    GROUND FAUIT CIRCUIT INTERRUMPTER

  • 79

    A SPECIAL BOLT THAT A SNAP-OFF SPINE IS A?

    TENSION/CONTROL BOLT

  • 80

    A SOLID FLAGIN A WELDING SYMBOL INDICATES THAT THE WELD IS TO BE PREFORMED?

    IN THE FEILD

  • 81

    SHACKELS SHOULD BE REPLACED WHEN THE CROWNS OR PINS ARE WORN BY MORE THAN?

    10%

  • 82

    THE TWO LEGS FORMING A CHOK NATRURALLY LIFTING TO PROXIMITY WHAT DEGREE ANGLE?

    45

  • 83

    A COMBINATION SQUARE WITHOUT A PROTECTOR HEAD IS A BLIND TO LAYOUT?

    85 DEGREE LINE

  • 84

    A TORQUE WRENCH MESSUAREMENT?

    RESISTANT TO TURNING

  • 85

    WHEN USING A MAGNETIC ____ THE POWER SOURCE SHOULD BE TAGGED.

    ALL THE PLUG

  • 86

    WHO IS THE RESPONSIBILITY FOR?

    EVERYONE