an example of a primary use for high carbon steel is

high carbon steels lose their hardness above a machining speed of

when cooled to room temperature high speed steel retains Rockwell hardness value of

straight carbide, cutting tools should not be used to machine plain carbon steel because they

polycrystalline diamond cutting tools are not effective on cobalt or nickel because

during ordinary, turning operations with a lathe tool, the edge that does most of the cutting is the

Delay tool bit relief angle affected by a 14 1/2° tool holder angle is the

if you take too light a feed on a workpiece

The type of grinding wheel you should use for rough, grinding carbides is

which is not a common nano oxide matrice

because of his strength, the best type of advance, ceramic cutting tool for mechanical, and where applications is

The advance ceramic that retains its straight at temperatures as high as 1400°C is

The advanced ceramic that is extensively used in electrical applications is

The size of a lid is designated by the maximum diameter of the workplace swung over the way distance between centers and

The item that permits used to remove the backlash between the compound rest, and the cross slide is the

you can use the carriage clamp screw only to lock the carriage in position when you are

The lever on the lathe apron you must engage to cut threads with a lathe is the

on a leave, adjust the Gibbs on the compound rest

The lathe Chuck that has the greatest holding power is the

The lathe chug that can hold duplicate pieces of irregular shape is the

when truing a faceplate for machining, your last option should be

when you take a light cut to true the face of a face plate, you should make only one or two

What item can you mount on a face plate to hold a work piece that is vertical surface

A characteristic that face place and dry place do not share is the

The lathe center use only with facing work, held between centers is the

The lathe center you used to support hollow work is the

The amount of eccentricity for an eccentric mandrel is determined by the

The Mandot type you should use to machine surfaces, concentric to threaded holes is the

The machine, a one diameter carbon steel rod with a selected cutting foot speed of 80 U determine the lace spindle revolutions per minute with the formula RPM equals CFS times four, divided by D which results in an RPM of

when machining, long work pieces with small outside damage to feed rates must be reduced

The amount of material that should be left on the outside diameter for finishing is

The least accurate method of facing to length is

The purpose of filleted shoulders is to

You can break a square corner by

A process of feeding a parting tool into the work piece and then moving it slightly to one side for clearance is

The method of cutting radii on the lathe that requires simultaneous coordinated movement of the carriage and cross slide is

The method of cutting radii on the lathe that requires a full scale, layout of the form of the work on a piece of thin sheet metal is

to cut a convex radius while using the compound rest you

Compared to speed for rough turning leg spindle speed for filing metal is

With the offset tail stock method of cutting tapers, as the length of the work increases the

One disadvantage of using the tailstock, offset method of machining tapers is

The lathe taper, turning attachment component that prevents backlash from developing in the cross slide during operation is the

To take depth of cut when using the taper attachment, use the

You can keep a drill from turning when you float it on the tailstock center by

when preparing for hand reaming you should rough drill a hole

to produce a very accurate hand, reamed hole you

The revolutions per minute you should use for machine reaming is

The end relief of a boring tool varies with the

The position of the boring tool in relation to the work for boring is

to prevent producing bell mouthed holes when boring

in the thread designation 1/4–20 UNC – 3B, the 3B represents a

Unless otherwise, specified all international organization for standardization, metric, threats are considered

Thread micrometers are designed to give a direct reading of thread

when you grind a thread, cutting tool for cutting unified threads, you grind the cutting edge to ensure an included angle of

The amount of side relief angle ground on a threading tool, depends upon the

During a threading operation takes successive cuts by setting a depth of cut with the

Before you cut internal threads on a work piece, you must bore the hole to the

During internal threading operation, positioned the compound rest

The main difference between cutting right hand and left-hand threads is when you cut

The size of the undercut machine in a shot as the star port for a left hand threading tool should be

The method of cutting multiple lead threads on the lathe that works best for cutting ACME, and square threads is

When you set the cutting tool center gauge for cutting taper thread, as you said it to the

they included angle on the a ACME thread is

How wide should you grind the point of a square 13 tool for cutting internal Square threads

when coming to the end of a cut while machining metric threads on a standard lathe you

The spindle speed you should use when power tapping a whole with a lathe is

if you’re considering a power tapping operation, restrict the operation to taps of at least a

The setting for your finish cut when you thread with a geometric dye is the

if you allow the work piece to stop without relieving the nursling tool, pressure the

if the diametrical pitch and work, blank diameter are not in relation to each other, the nurl

When dressing a grinding wheel on the post grinder, the final depth of the cut should be

During an internal grinding operation, the grinding wheel and work piece should rotate

by using the micrometer carriage stop, you can position the carrots to a tolerance within

The factors use identify milling machines are

The size of a milling machine is determined by the

Before you tighten in or loosen the arbor nut on a horizontal milling machine you should

The backlash and the vertical feet screw of a milling machine table is eliminated by

The feature on a milling cutter that keeps the cutter tooth from rubbing in the cut as it passes is the

The feature of a plane milling cutter that reduces shock and permits a smooth cutting action is

The type of milling cutter you would selected, cut off work or mill narrow slots is the

The corner on a shill mill easiest to grind is the

While rotating in mills with a right hand cut are designed to

The type of email that is best for interrupt the cuts is a

what is the width and diameter of a 404 wood rough key seat cutter

The number 54M on a mailing machine taper adapter means the adapter has a number

if you have a spindle speed of 80 revolutions per minute a chip thickness of 0.004 inch and a card with a 12 teeth what is the correct feed rate determined by using the formula F = T x NT x RPM

The process of milling, a flat surface parallel to the cutters, axis is an example of

The process of mailing a flat surface perpendicular to the cutter axis is an example of

When you select a milling cutter for face milling select one that

If after taking your first boring cut you notice the hole is not properly located adjust the

To mail a square ended keyway in a shaft. You should use a.

you align the index head with the longitudinal axis of the milling machine table by using

solve the plane indexing solution to machine a hexagon on a round workpiece use of formula T = 40 divided by by N

when you turn a index crank one complete turn on a 40:1 index the work rotates

The type of indexing attachment that is quick and easy to set up and is adjusted by the use of a clutch lever is

The milling machine attachment used to machine complex. Compound angles is the.

when using the Cartesian system, the spindle axis is

If line segments do not begin, and in at the same point when creating geometry for a computer numerical control

The purpose of a post processing a completed computer, edit design/computer. Edit manufacturing file is it

If the toilet offset is not set during the programming phase